Question about 1998 GMC Jimmy

1 Answer

Cam position sensor

Where is the cam positioning sensor found on a 1998 gmc jimmy?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Cam sensor is located in distributor.

Posted on Oct 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 jimmy will turn over but wont start


check that the crank position sensor is ok as it has to work to sense the correct time to allow ignition and spark

Jan 14, 2013 | 1998 GMC Jimmy

1 Answer

PO102 and PO340 on 1997 GMC Jimmy


PO102 = mass airflow circuit low. Means there's a problem with the mass airflow sensor or circuit. Could be the sensor is disconnected, dirty, or faulty. PO340 = camshaft position sensor circuit. Could be ground wire disconnection, camshaft position sensor failed, PCM is failing, or even the crankshaft position sensor has failed. Good luck. Let us know how it turns out.

Nov 07, 2012 | 1997 GMC Jimmy

1 Answer

1998 gmc z71 surges in drive p1345


The P1345 means SGC (Cam Position) sensor circuit malfunction/crankshaft position-camshaft position correlation
P0300 means random/multiple cylinder misfire detected

mpps ecu chips

Aug 07, 2012 | 1998 GMC Sierra

2 Answers

1998 GMC Sierra 2500 5.7L hard cold starts last month, now won't start cold w/o a little carb cleaner in intake. Codes for oxy sensors, mass air sensor and crank/cam position. Drove today, no power just...


starting definately has a lot to do with the crank/cam position sensors, but it wouldnt have nothing to do with hot or cold weather, oxygen sensor will make the vehicle run too rich if its out, you will smell fuel very strong out the exhaust, that could make it run sluggish also, and usually if the mass air flow sensor goes out the vehicle wont start at all...

Nov 27, 2010 | 1998 GMC Sierra

1 Answer

I need to knwo where the cam position sensor is on


cam sensor is in the distributor. also know as the pick-up assembly.

Nov 10, 2009 | 1999 GMC Jimmy

1 Answer

My truck is stuck in 4LO and it won't come out of 4LO.


Likely either a shifter position sensor, transmission position sensor, or a differential position sensor. Had same issue w/ my Montero and it ended up being one of the 5 sensors on the transfer case. It was pretty tough to get to, so replaced all 5. That fixed it.

Jul 16, 2017 | 1998 GMC Jimmy

1 Answer

Where is the cam shaft position sensor located on a 2001 gmc 5.7 , and also the crank position sensor?


If this is a 5.7L the cam sensor is in the distributer and the crank sensor is in the timing cover

Dec 16, 2008 | 1995 GMC Jimmy

1 Answer

TPS in a 1998 GMC Jimmy


the tps is ususally at the side of the throttle body opposite where the throttle cable / tv cable mount.
sometimes it won't start, run, or run erratically. there are ways of testing this unit (by output voltage) before you commit to buying a new one. to test it you will need a dvom (digital volt ohm meter).

just a note: straight from the book... "a broken or loose tps can cause intermitten burst of fuel from the injector and an unstable idle because the ecm thinks the throttle is moving."

Sep 22, 2008 | 1998 GMC Jimmy

Not finding what you are looking for?
1998 GMC Jimmy Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...