Question about 1998 Jeep Cherokee

1 Answer

How to remove ignition switch on 98 jeep cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 58 Answers

Generaly you need a working key to remove an ignition Barrell.

You have to partialy turn the lock to a point where a little plunger can be depresed, allowing you to pull the barrell out.

THis is only general info, you will have to have a close look.
If you dont have the key, your in trouble.
Good Luck, Get to know a friendly mechanic.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to remove ignition switch on a 1990 jeep cheeroke


Remove lower instrument panel trim. remove 2 steering column to dash/brake support nuts and lower steering column. remove screws holding ignition switch to column and lift switch off of lock rod. first remove black harness connector, then remove white connector from switch.

Apr 10, 2010 | 1990 Jeep Cherokee Limited

1 Answer

My 98 jeep grand cherokee wont start. It doesnt even click or turn over. battery is fine, headlights, dome lights, all go on. Radio doesnt work with ignition on. I checked ALL the fuses, I replaced the...


fuse 8 40a supplies power to starter relay and ignition switch, to close the starter solenoid and engage the starter which draws directly from the battery. check to see that the starter relay is closing, if not ensure that the park neutral switch is not faulty (open circuit), it provides path to close relay (ground side) on the 85 - 86 terminals. if the starter relay does not close the starter will not run. if you have a spare relay swap out the relay for a quick fix attempt. hope this helps

Jan 28, 2010 | 1998 Jeep Cherokee

1 Answer

Ignition switch locked 98 jeep cheerokee how do u get it unlocked


Replace the ignition switch, yours is broken and or worn out.

Dec 29, 2009 | 1998 Jeep Cherokee

1 Answer

How do you remove the ignition switch from a 1993 jeep Cherokee? Apparently the key switch activates a lever or or rod inside the steering column that operates this switch but how do you get it apart? we...


Disconnect negative battery cable, remove upper and lower covers (three screws); remove the ignition switch mounting screws.

Pull switch away from the column and remove the connectos from the ignition switch.

Also I suggest check the 93ZJ-Secc-8D-Ignition-Systems for more details and graphics.

I hope helps with this (remember rated this help) Good luck.

Dec 21, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Ignition coil on a 95 jeep grand cherokee


on 98 and earlier v8s it is located beside the air filter box.

Oct 27, 2009 | 1995 Jeep Grand Cherokee

2 Answers

1994 jeep grand cherokee rplacing back hatch and passenger door


Just call the part stores and dealership head quarter the dealers ususally wont give you that info, also junk yards will help you out a lot also.

tepfy

Apr 10, 2009 | 1994 Jeep Grand Cherokee

1 Answer

1993 Jeep Grand Cherokee Laredo wont drive when put into gear


No, not with out a lot of work. Electronics are most likely different on the 2 also.

Mar 11, 2009 | 1993 Jeep Grand Cherokee

1 Answer

My 98 jeep wont stay running unless i turn and hold key almost to start position


Sounds like your ignition switch is going bad. Not your lock cylider, but the switch.

Mar 05, 2009 | 1998 Jeep Cherokee

1 Answer

How to remove the ignition switch in a 1993 Jeep Cherokee?


you need to remove steering wheel and you will see how its done once you get inside

Dec 10, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
1998 Jeep Cherokee Logo

Related Topics:

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...