Question about 1999 Dodge Ram

1 Answer

I need step by step instructions on removing and installing a water pump for a 318 Dodge motor... need torque specs also.

Posted by on

  • yadayada
    yadayada May 11, 2010

    no one torques a water pump.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,081 Answers

1. Drain Coolant 2. Take fan clutch off 3. Take fan shroud off 4. Take the serp. belt 5. Take the brace on the A/C and Alt. bracket 6. Take the A/C compressor off the bracket (but do not recover freon) 7. Take the idler pulley off 8. Take the bracket off but leave the alt. attached to bracket 9. Pull the wiring off the temp.gauge on the intake by the tstat housing 10. Take the bypass hose clamps off by using a hose clamp pliers. 11. Take the lower radiator hose off 12. Take the bolts out of the waterpump and take the pump off with a little tap with a hammer or pry it off. 13. Clean off old gasket 14. Install in reverse

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

1 Answer

How to replace waterpump


step 1. drain cooling system.
step 2. remove battery and battery tray.
step 3. remove drive belt.
step 4. remove water pump bolts ( 318 ).
step 5. remove water pump ( 300 ) and water pump gasket ( 314 ).discard gasket.
step 6. inspect and clean gasket mating serface.
step 7. install new water pump and gasket and tighten bolts to 89 in. lbs.
step 8. install drive belt.
step 9. install battery tray and battery.
step 10. fill cooling system.


Book time is 1.5 hours ( this one is what we call a gravy run ) good luck

1_18_2012_1_26_20_pm.jpg

Jan 13, 2012 | 2006 Chevrolet Impala

1 Answer

Overhauling motor need all torque spec.


To save incorrect information being passed along.
Invest in a Haynes Manual, for your Make and Model. These are available at Checkers and Auto Zone, and will give you all the step by step instructions, and exact sequence and torquing specs, to enable you to complete the task correctly.

Regards, DT

Mar 02, 2011 | Dodge Dakota Cars & Trucks

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

1 Answer

HOW TO CHANGE WATERPUMP 1999 INTREPID 2.7


    Prepare the Dodge Intrepid
  1. Step 1 Lay out a drop cloth underneath the Dodge2_bing.gif Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
  2. Step 2 Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
  3. Step 3 Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
  4. Step 4 Use a grease pencil to mark on the timing belt2_bing.gif its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
    Remove the Damaged Pump
  5. Step 1 Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
  6. Step 2 Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
  7. Step 3 Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
  8. Step 4 Clean off the mounting area with a shop rag.
    Install the New Pump
  9. Step 1 Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
  10. Step 2 Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
  11. Step 3 Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
  12. Step 4 Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
  13. Step 5 Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.

Apr 04, 2010 | 1999 Dodge Intrepid

1 Answer

Looking for water pump torque spec for dodge 318


Water pump attaching bolts: 30 ft-lb
Fan-to-water pump attaching bolts: 200 inch-pounds

Nov 05, 2009 | Dodge B Series Cargo Cars & Trucks

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

1 Answer

Water pump


These numbers are in foot pounds water pump attaching bolts=30  water pump pulley attaching bolts=20 fan clutch to fan blade bolts=17 fan assembly to drive hub nut=42 thermostat housing bolts=17

Jul 18, 2008 | 1995 Dodge Ram

Not finding what you are looking for?
1999 Dodge Ram Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...