Question about 1997 Ford Escort

1 Answer

If the crankshaft position sensor on my 1.8td escort was slightly off would this stop the car from starting

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 149 Answers

Yes

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft Position Sensor ford escort zx2


make sure its the problem-if a code reader was used-thats usually a general idea--a data stream must be run to confirm--independent shops do that---- a haynes manual at a partstore or library has service books that techs use

Jun 04, 2014 | 1999 Ford Escort

2 Answers

Location of cam and crank position sensors


The cam sensor is located at the front right front side of the cylinter head, while you are facing the engine.---------- The crank position sensor located below the pcv valve that is located on block not the valve cover, its below the exhaust manifold. You will have to remove the catalytic converter to see the exact view of both the sensors. The camshaft sensor is on the head. The crankshaft sensor is in the block, just below the exhaust manifold. ------------ Thanks.Helpmech.

Nov 12, 2010 | 2001 Ford Escort ZX2

1 Answer

Car cranks but won't start. Has no spark. It does get fuel in, just changed the ecm, the crankshaft position sensor and the coil pack. Any ideas?


Could be a crankshaft position sensor fault or even a ignition coil fault. I suggest u check the stored fault codes in the PCM first. If there is no ckp sensor codes in the system and a new coil doesn't fix the problem it's possible the coil has spiked the PCM . If this is the case a new coil and PCM should be installed. The engine rpm and signal from the coil is picked up from the ckp sensor.

Sep 29, 2010 | 1999 Ford Escort

2 Answers

Changed timing belt on my 99 ford escort zx2 car no


if you have a no spark scenario i would check your crank sensor located at the top left side of the harmonic balance pulley.the crankshaft (about 11'oclock) a 2 wire plug with a sensor on it check to see if it is damaged or unsecured. this sensor can cause no spark if not working correctly. This sensor is based of frequency not voltage testing is difficult, just make sure that there isnt too muck air gap. and that it is secured.Lastly may want to check timing possible that the belt has jumped some teeth and she has fallen out of timing. maybe a bad tensioner The coil will adapt i think up to 10 degree, ****** or advance. Good luck

Apr 18, 2010 | 1999 Ford Escort

1 Answer

I have a 99 Ford escort zx2 and the enigne quit while is was driv


This is a common problem for a crankshaft sensor failure. When it fails, the engine can not start since the ECM doesn't know the proper position of the crankshaft to give ignition according to TDC (top dead Center). Therefore it doesn't matter how strong your battery is, it won't fire. The fire is only happens when an ignition happens at the highest compression point when a piston is at top and this is reported by the crankshaft sensor. Have this checked out and replaced. Good luck.

Dec 12, 2009 | 1999 Ford Escort

1 Answer

I would like to know were is the crank sensor


It is under the exhaust manifold
Disconnect the battery ground cable.
Raise the vehicle.
Remove the exhaust manifold.

Disconnect the electrical connector from the Crankshaft Position sensor (CKP sensor).

Remove the crankshaft position sensor.
Remove the bolt.
Remove the crankshaft position sensor.
INSTALLATION

Lubricate the O-ring lightly with engine oil XO-5W-30-QSP or equivalent meeting Ford specification WSB-M2C153-F. NOTE: Inspect the O-ring for damage; replace if requi

Dec 04, 2009 | 2001 Ford Escort ZX2

1 Answer

Intermittent miss and no start


faulty crankshaft position sensor is the most likely cause.

Oct 07, 2009 | 1995 Toyota Camry

1 Answer

Car idles slightly higher in park or stop and jerks back


Have the car scanned for a trouble code. It seems like a sensor problem to me. Either the idle position sensor or the crankshaft position sensor may be going bad on it.

Apr 08, 2009 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

214 error code


CID sensor and camshaft sensor are the same the crankshaft sensor is located on the front lower cover by crank pulley

Nov 30, 2008 | 1999 Ford Escort

Not finding what you are looking for?
1997 Ford Escort Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...