Question about 2004 Ford Ranger

Open Question

How do a bleed a 2004 Ford Ranger Master Slave Cylinder?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replaced slave cylinder 2004 ford ranger 4x4 still no pedal

I had the same problem with my 1995 1500 p.u.. Assuming your clutch slave cylinder is the concentric style. If not disregard. I hate that set up. what the hell was wrong with the old outside of the bell housing slave/ mechanical style fork and throw out bearing bla bla? Its because ford as well of the rest of the lovely auto makers decided long ago to make them as hard as hell to repair on you own. Ive been told theres a spsecial tool just for this bleeding task. Pobably. They make those tools to sell to us so they can further profit from us poor suckers.Also I wonder on your model if its concentric, does it have the difficult sized bleeder valve as mine did? or have they gotten a little more user friendly? doubt it. In my case as this style is a closed system I followed the bleeding intructions to a tee. That did get alot more clutch action for me, after 15 attempts.However I do believe the problem after looking and further inspection under the dash? look up under the dash and inspect your pedal rack and frame. I found mine was cracked and the cause of poor aliegnment. check for that rite away. I located another rack but before I got around to replacing it, the tranny blew, and the trucks sitting on my dads property. Its still a danmed good truck and one of these days I will get on it again. Anyway up untill the tranny blew I was never able to get more than half the distance from the pedal and besides the rack problem I would love to know the bleeding anser, that is if Im off target. Going to be up against it again when I replace that transmission. Hope this helps a little. Food for thought maybe? If you find out something more helpful post it so I will know too.

Posted on Dec 22, 2008

Ad
moparownr
  • 667 Answers

SOURCE: im having difficulty in bleeding a cluch o a ford

clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Posted on Apr 08, 2009

  • 490 Answers

SOURCE: i have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0

Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Posted on Aug 13, 2009

  • 422 Answers

SOURCE: I have a 1987 Ford Ranger that I replaced the

your throwout bearing is probably bad (most likely)

Posted on Nov 19, 2009

Testimonial: "Thank you for your response. I will look into that possiblity as well but it was replaced along with the slave cylinder."

  • 14036 Answers

SOURCE: I am replacing the slave cylinder hose on a 1994

YOU NEED A DISCONNECT TOOL T88T-70522 OR EQUIVALENT. YOU CAN BUY DISCONNECT TOOL AT ANY AUTO PARTS STORES.

Posted on Oct 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed 89 ford ranger 4x4 clutch


there is a bleeder screw by the transmission slave cylinder that you bleed the air out.just pump the clutch pedal a few times hold the pedal to the floor and have someone crack open the bleeder screw to bleed the air out then close it and repeat.make sure the master cylinder for the clutch doesn`t go low.

Nov 02, 2011 | 1989 Ford Ranger

2 Answers

The clutch filud was empty filled but still can't ingae clutch. Is there a bleeder some were


There should be a bleed valve on the slave cylinder but some of them are quite difficult to get to. If the master was empty you need to check the line for leaks and the master and slave cylinders for leakage.

Jan 16, 2010 | 2002 Ford Ranger Regular Cab

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

1 Answer

I have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0 RECENTLY LOST PEDAL ON MY CLUTCH. REPLACED MASTER CYLINDER, SLAVE CYLINDER, AND THE CLUTCH PACK, HAVE FLUID THROUGH BLEEDER VALVE ON THE SLAVE BUT CAN NOT...


Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Aug 13, 2009 | 1998 Ford Ranger SuperCab

1 Answer

2003 Ford Ranger-5 Speed. At times is very hard to get into gear


Your clutch is not releasing all the way. (Assuming the problem is not internal to the transmission) Bleed the system. If that doesn't work, rebuild the clutch master cylinder and slave cylinder and bleed again.

Aug 12, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

2006 ford ranger can not bead the slave cylinder


I dont want to make you feel silly but it seems like you loosened a grease nipple and not a bleed screw. A small amount of fluid (if the slave cylinder is not new) is normal. Their is no way grease can get into the fluid system. Take off the feed pipe to the slave cylinder Try pumping the pedal or use your vacuum pump from there.Get someone to pump the pedal holding your finger on the end of the pipe to see if their is any preasure comming that far if not its your master cylinder if you have preasure check the slave cylinder again for a bleed screw. It seems more like the master cylinder unless it ran out of fluid otherwise how did air get in. You should also check if the slave cylinder or the bar comming from it is adjustable Sometimes their is a screw on the bar others have oblong holes to move the slave cylinder back or forward

Aug 09, 2009 | 2006 Ford Ranger

1 Answer

How do i bleed a clutch a on a 92 ford ranger


U will need to buy a Mityvac brand suction bleeding tool to **** the fluid from the master to the bleed port on the slave cylinder at the trans.
this is the only easy way I have found. u can buy this tool at NAPA and Carquest stores

Jun 25, 2009 | 1992 Ford Ranger

1 Answer

We are not getting pedal on the clutch after bleeding the slave


Here is your issue, I have an '03 with the same tranny, the problem is most likely the slave cylinder which requires a pull of the transmission the part is 50 bucks and I did this in about 10 hours on my back, by myself and just a little swearing. I replaced the whole thing the pressure plate, clutch disk and slave cylinder as I was not going to do this again.
The other side of the issue is the master cylinder in which I find if the Slave is bad the master is also bad, hence the pedal dropping to the floor.
The bleed is simple it is a gravity bleed. Loosen the bleeder and let it run. then after you verify there si no air you can pump up the master and it should work fine.
this is a poorly designed system as the slave cylinder on the mitsubishi tranny is inside the bell housing.. good Luck

Jan 14, 2009 | 2004 Ford Ranger

2 Answers

Brake fluid in brand new 1989 ford ranger clutch slave


no it doesn't come filled basically you bleed it like a brake system. Fill the master cylinder and pump the clutch, there is a bleeder on the slave cylinder

Dec 08, 2008 | 1989 Ford Ranger

Not finding what you are looking for?
2004 Ford Ranger Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...