Question about 1999 Jeep Cherokee

1 Answer

Turn signals and hazard light dont blink, just stay on

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

Replace the flasher unit. auto zone will do this

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alpha Romeo 156 My Left hand indicator light stays on continually, does not flash. and when I turn the hazard light switch on both indicators continually glow.


Generally speaking, symptoms of a bad or failing turn signal bulb are usually the culprit...in your case, either it's the front left or rear bulb. Varies for different vehicle makes...common signs include:
  1. turn signal light staying on solid
  2. or blinking very fast
  3. or either sides of the bulbs stop blinking altogether.
To test this, make sure you reconnect everything you disconnected.
Turn the left signal light on; go to the front of the vehicle, is the turn signal bulb illuminated? If it lights up, even though it is not blinking obviously the bulb is okay. If it doesn't, replace it- problem solved. You'll do the same procedure for the rear turn signal Is that lit up? If not replace the bulb and the problem is solved.
Another common failure is when the turn signal blinks really fast, same procedure as mentioned above.
If both bulbs for the left side and right side illuminate but don't blink, the problem is in the steering column turn signal switch.
If the left or right side blinkers don't work properly at all...then check the integrated hazard warning/turn signal flasher relay- that may be defective; again, that's usually the case if both sides of the signal light don't work.
If you are blowing any fuses related to the flasher system, you have an electrical overload in the turn signal circuitry.

Feb 12, 2017 | Cars & Trucks

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

1989 cutlass supreme sl turn lights work but dont blink


CHECK THE HAZARD/FLASHER IN THE FUSE BOX CHECK OWNER MANUAL IF YOU HAVE IT

Aug 19, 2012 | 1989 Oldsmobile Cutlass Supreme

1 Answer

83 Chevy S10 - the right blinker just stays lit, won't blink and no lights come on the right side at all.


put the hazard lights on and see if they all blink, if not, check the bulbs that dont blink. if all blink, (front and rear), the turn signal switch could be bad. putting the hazard lights on, checks the bulbs and wiring.

Sep 16, 2011 | 1983 Chevrolet S-10

3 Answers

Turn signals dont work on 1993 skylark. all bulbs are good. hazard lights blink fine. turnsignal dash light stays green and doesnt blink


There are 2 separate flasher relays. 1 for the turn signals and one for the hazards. I believe you have a bad flasher relay for the turn signals. The location of that is in the front seating area on the drivers side, under the dash on the drivers side of the steering column, mounted on support bracket. I provided a picture of what it should kind of look like although the picture I gave you is an aftermarket one so the color and such may be a little different but will look the same. Don't get it mixed up with the hazard relay which is located in the front seating area on the drivers side under the dash above the kick pane lmounted on top of the convenience. I am almost 100 percent sure the flasher and hazard relay are the same so if you want to just swap them out in order to have turn signals that should work. You won't have hazards however. I hope this helps you and good luck.


clifford224_215.jpg

May 07, 2011 | 1993 Buick Skylark

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

2 Answers

Brake light/turn sigs dont work.But lights are on?


Ok, GM had a problem with their hazard light switches in the years of around 2001-2005. These caused some bizarre workings concerning the hazards, lights, turn signals, etc. The circuits overlap, and when the switch malfunctions, it makes for some odd happenings. Normally, when the hazards are on, they cancel out the brake lights and the turn signals, since they use the same circuits. The normal taillights use a different filament in the same bulb, which is why they light up brighter when you press the brakes. The aftermarket has come up with replacement switches in response to these inherent problems, so do not get your switch from GM. Places like RockAuto.com will sell these, though not necessarily this place, it's just the one I use. Usually, GM put these in the steering column, so replacement can be tricky for the average person, as it involves taking apart some of the steering column.

Feb 22, 2010 | 2004 Pontiac Grand Prix

1 Answer

2004 monte carlo. Turn signals dont work. The stalk still works with other functions, such as wiper, brights. The fuse is fine. Could it be a bad relay? When u push the stalk up or down nothing happens on...


try pressing the hazards on and off if they still don,t work replace the flasher unit. it is built into the hazard switch( all one unit ) change this and all will be good.

Aug 30, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Turn signals won't blink


relay is bad turn signal relay

Jul 31, 2009 | 1998 Dodge Durango

Not finding what you are looking for?
1999 Jeep Cherokee Logo

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...