Question about 2003 Chevrolet Tahoe

1 Answer

On my 2003 chevy tahoe, the braking pedal vibrates when braking and I can't think of any possible solutions... When going on a city limit and we start braking it would not vibrate but like until the we are going around 5 miles an hour right before stoping. On a highway or any normal speeds it would not vibrate. Sometimes if the braking light comes on, the problem goes away, but if you turn the vehicle on again it would have the problem again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 909 Answers

The brakes vibrating could mean a rough spot on the disc, a warped disc or faulty ABS.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can l fix a brake pedal that is to high up on a 2003 grand cherokee laredo


There is a rubber limit stop above pedal. If missing pedal will be a bit high. Otherwise, brake light switch limits upward travel. No other adjustment is possible without cutting and rewelding pedal which could limit travel, change leverage, and void warranties. Adjust seat instead.

Feb 10, 2015 | 2003 Jeep Grand Cherokee

1 Answer

2002 chevy tahoe no front brakes only rear brakes


IT appears that only half of the master cylinder has bled properly. Try loosing the pipe nuts at the m/cyl and gently pump the pedal until you get fluid out of both lines. Then re-bleed the system starting at the longest line first ending at the shortest. Some master cylinders have a plunger fitted in the middle of the cylinder and this is there to still have brakes if a line fails. It may be necessary to remove it an plug the hole temporarily while you bleed the system as to stops one piston in the cylinder from moving and allowing proper bleeding

Jul 17, 2013 | 2002 Chevrolet Tahoe

1 Answer

My 2009 Chevy S-10 Blazer's anti-lock brake system activates when coming to a stop on dry pavement. The typical anti-lock sound is heard and the brake pedal pulsates. There are times when it feels like the...


check the rotors for scoring,worn rotors will "feel"like the abs is coming on due to the vibration caused.and will account for the extended stopping distance.

Dec 09, 2010 | 2001 Chevrolet Tahoe

1 Answer

How to install the brake light switch for 2003 chevy tahoe


Look under the dash on the drivers side. The switch will directly above the brake pedal. You should see the switch with an electrical connection you can unplug and the nut to take off to remove the switch. Before you put the new switch in notice where the adjustment is on the old switch and put the new one in about the same position. Once installed you will most likely have to make a small adjustment on the adjustment nut and thus the hold down nut. A small adjustment makes a lot of difference. Adjust the new switch so that when the brake pedal is depressed about 1/4 inch the brake light are activated.

Jan 11, 2010 | 2003 Chevrolet Tahoe

4 Answers

Emergency brake light stays on on my 03 tahoe


I have an '03 Chevy Tahoe and I had a similar problem. I discovered that there is a bare copper striking plate or tab that the medal emergency parking brake pedal touches when the emergency brake is set. It turns on the idiot brake light in the dash. It had broken off and the light stayed on all the time with the say issue of chiming whenever the vehicle is in motion. You or the dealership must replace that striker plate to fix the problem.

Jun 02, 2009 | 2003 Chevrolet Tahoe

2 Answers

Pulsating and vibrating brakes on 2003 chevy express, new pads and rotors


Rust build up is commonly found on the hubs sandwiched by the rotors/hubs

May 15, 2009 | 2003 Chevrolet Express

1 Answer

Does it matter what gear to drive in?


If the speed limit is 30 and a lot of stop and go the transmission will be less stressed in 3rd.

Dec 19, 2008 | 2003 Chevrolet Tahoe

4 Answers

2001 tahoe emergency brake will not hold


Ah homie it is your parking brakes, most important thing when doing front or rear brakes is that u need to resurface rotors and drums as well, if u did this already then just simply bleed your rear brakes- from the furthest drum first and so on down the line.
Chevy brakes aren't that well designed like other vehicles but they do function well & correct if done right and use organic or softer material if possible to prevent warpping to the front rotors then you'll have very shakey steering wheel when trying to brake.


Chino

Aug 05, 2008 | 2006 Chevrolet Tahoe

Not finding what you are looking for?
2003 Chevrolet Tahoe Logo

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...