Question about 2002 Volvo S80

1 Answer

Engine overtemp overtemp indicator came on ,put in garage to look at and went off overnite without doing any thig to it. Now its back again????

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Master
  • 302 Answers

Check coolant level

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does an engine indicator lamp means?


The check engine light could indicate many different faults! The only way to be sure is to get the fault codes read! This will indicate where the fault is! If you do not have a code reader then take it to a garage to have this done!

Dec 04, 2014 | Nissan Cars & Trucks

1 Answer

How do I turn off engine management warning light without taking it to a garage ?


Normally you would remove the fuse supplying power to the car's computer, for 30 seconds. However the light will just come back on again, because the computer is sensing a problem and trying to tell you.

Sep 01, 2014 | Cars & Trucks

1 Answer

Diesel fault finding


Difficult to say here without looking myself ,suspect that you may need to bleed the fuel system thats all you need to do but did the oil light come on ,not the engine light but the oil can symbol if so you may have damaged the engine but it should still start even if the bottom end of the engine is making a banging noise.What did the garage say when it wouldnt start?

Jan 04, 2014 | BMW Cars & Trucks

1 Answer

The malfunction indicator light came on about a month ago in my Suzuki Alto (2005) and I took it to the garage and was told there was a misfire in cylinder 2. I was told it was fine so they reset the light...


If the code has been a misfire in the same cylinder every time, the problem is very likely the ignition coil for that cylinder. When the ignition coil first starts to go, the malfunctions will be sporadic and therefore difficult to troubleshoot. The ignition coil can be tested for resistance on both primary and secondary windings in the coil to prove it is failing.

Oct 30, 2013 | Suzuki Alto Cars & Trucks

1 Answer

Car struggles to start from cold; when it starts, it immediately dies out again.


have the fault codes read
indicates a problem ambient temp sensor, baro sensor or MAP/VAF sensor problems
reading the fault codes is something the garage should done forst

Mar 12, 2017 | Cars & Trucks

1 Answer

My 1990 toyota 2.8 pickup ( african import) got low on oil without indication and i thought had seized. got it back to the garage and sorted out pipe ,oil indicator and refilled with oil. It started up and...


Damage has been done to the engine, the noise you hear are the piston rod bearing ( knocking lower part of engine ) you can try putting in a crank kit and have the piston rods mechin but will not last very long, will start to knock again, best bet to replace engine,good luck.

May 24, 2010 | 1990 Toyota Pickup

1 Answer

Factory garage door opener


If this is the 3 button HomeLink Transmitter usually centered overhead above the rear-view mirror, this should work:

While the engine is turned off follow these steps to program up to three channels:
1. Decide which one of the 3 channels (one of the 3 HomeLink buttons) you want to program.
2. Press & hold the desired button through step 3.
3. When the HomeLink indicator light begins to blink slowly(this may take up to 30 seconds), hold your hand-held garage door remote about 1 to 3 inches away from the buttons & then press and hold the button on your garage door remote. Continue to hold both buttons until the indicator light on the HomeLink begins to flash rapidly(this may take up to 90 seconds).

If it still doesn't work, make sure the batteries in your garage remote are not weak, and try again moving the remote back & forth and left & right or turning it upside down while programming.

Also note HomeLink will not work with older garage door openers, especially not with ones manufactured before April 1st 1982.


Feb 18, 2010 | 2005 Buick Rendezvous

1 Answer

Overdrive not working


try trans x stop leak it willn rejuvinate the seals

Jun 14, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Volvo S80 Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...