Question about 1989 Ford F 150

1 Answer

Ned help to change rotor on 1989 f150 4x4 - 1989 Ford F 150

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Whic rotor are we talking about? the rotor cap on the distributer or the rotor on the wheel?

Posted on Oct 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1989 chevy k1500 wont start after changing distributor and rotor

very good but did you check that the no1 piston was on tdc firing before you replaced the distributor . You may be 180degrees out on the firing order.

Apr 09, 2014 | Cars & Trucks

1 Answer

1989 isuzu trooper engine loping


Sep 02, 2012 | 1989 Isuzu Trooper

1 Answer

I have a 1989 dodge dakota sport and im not getting any spark at the plugs ive changed the coil, distributor cap,rotor button and still no spark and changed the stater any help?

check your fuses or your timing is off if your timing is off get your timing light if that dont work and is the motor even cranking over

Jan 09, 2011 | 1989 Dodge Dakota 2WD

1 Answer

What will cause the steering to shake when Brakes applied at speeds of 40 miles per Hr. and up?

you have warped disc rotors you will ned to get them machined or buy new one, you can try a new set of brake pads first but most lik;ey will be the rotors hope this helps

Aug 17, 2010 | 2004 Acura TSX

1 Answer

Got 1989 dodge ram van 5.2 at idel it run rought

Check for a leak at the intake manifold you can use some soap in a spray bottle spray along the intake and heads it will change the idle if its leaking
let me know if this helps

Jul 13, 2010 | 1989 Dodge Ram 50

1 Answer

I changed the back right tire on my 1989 suzuki swift gti, and now the break light won't go off and the rotor is grinding. It was fine before but i don't know how to fix it, what should I do?

as changing a tyre has nothing to do with the other faults you describe,try changing the bulb for the brake light.and check rotors/brake pads for wear.

Mar 26, 2010 | 1989 Suzuki Swift

1 Answer

Need help with front brake rotor removal

if your rotors are what they call split rotor just remove the brake caliper there are t pins or bolts as some people call them take a screwdriver and insert it between the brake shoe and the rotor pull toward you and the brakes will retract (front only)
lift off the caliper with the brakeshoes.. the rotor should be able to be tapped off altho if it is rusty it may take a couple of good hits /// same for a full rotor execpt you have to take the bult off the front of the spindle this type has bearings & seal in the rotor
they should be replaced when changing this type
put on new brakes and your ready to go

Mar 05, 2010 | 1989 Ford F 150

1 Answer

1989 chevy 1500 v8 wont start out of the blue changed icm,coil getting fuel no spark draws current at the coil when key is turned

That old of a vehicle you might want to take the cap off and check to see if the shaft is turning. You will be able to see the rotor turning. Also look inside the cap and see if the rotor and cap are good inside.

You said you changed the ignition coil module, not sure if you mean you changed the coil too, if not change that.

hope this helped

Feb 23, 2010 | 1989 Chevrolet K1500

1 Answer

Replacing rotors

Those should be "fall off" rotors. If there is rust in the center of the rotor where it meets the hub, just use a hammer to break the rust loose and the rotors should break free and the rotors should come off. Spray the area with a rust lubricant first. You shouldn't have to beat the snot out of them, just a firm tapping around that area. Hope this helps.

Jun 13, 2008 | 1989 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides