Question about 1983 Chevrolet Malibu

1 Answer

Remove left front fender 1967 Chevelle

How do you remove left front fender 1967 Chevelle? Is there an online diagram of the nuts and bolts?

Posted by on

  • Anonymous Mar 16, 2014

    I need fender skirts for my 1967 olds for door 98

  • Anonymous Mar 29, 2014

    how to remove left front fender


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 24 Answers

There are quite a few bolts on this fender. One on the bottom of the rocker, one between the the door and fender on the "A" pillar, one on the cal, one on the firewall then several on the inner fender and several on the radiator core support. after these are removes you need to take ou the head light assembly and you should have a fender brace under the front of the car. Hope this helps.

Posted on Oct 07, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove left front fender 1980 300sd

Remove marker lamp and headlamp assemblies.

Remove bolts behind lamp assemblies holding fender to frame of car.
Remove bolts along seam hidden under hood.
remove left front wheel and splash guard.
remove more bolts in wheel well
open left door, remove bolts in sill by door hinges.
Take lots of wires and stuff loose from fender.
Tada, fender is removed.

Dec 19, 2014 | Cars & Trucks

1 Answer

Any one have a diagram or drawing of fuse box 1967 chevelle/el camino

I have 1967 chevelle need a wiring diagram for auto console.I got the wiring but how to put it in?

Apr 01, 2012 | Cars & Trucks

1 Answer

How do i change the heater core

big job. instrument panel has to come out.

Section 01-12: Instrument Panel 1997 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/16/2000
Instrument Panel SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Radio Removing Tool T87P-19061-A
Removal and Installation
  1. Raise vehicle on hoist.
  2. Remove RF wheel and tire assembly. Refer to Section 04-04.
  3. Remove three nuts in radiator coolant recovery reservoir area.
  4. Remove bolt retaining front fender apron (16054) to front fender (16005).
  5. Position front fender splash shield out of the way.
  6. Lower vehicle.
  7. Tag and remove main harness connector from jumper harness (located in front of blower motor).
  8. Remove LH instrument panel lower insulator (043A89) and instrument panel lower insulator (043A88).
  9. Remove steering column. Refer to Section 11-04.

    Instrument Panel Lower Insulators


    Item Part Number Description 1 04320 Instrument Panel 2 N807296-S Cap 3 388577-S Push Pin (6 Req'd) 4 043A88 Instrument Panel Lower Insulator, RH 5 043A89 Instrument Panel Lower Insulator, LH 6 - Module Bracket (Part of Module) 7 13466 Miniature Bulb 8 043A88 Instrument Panel Lower Insulator, RH 043A89 Instrument Panel Lower Insulator, LH
  10. Remove RH cowl side trim panel (02344) and LH cowl side trim panels (02345).
  11. Tag and disconnect wiring connectors in LH and RH cowls.
  12. Remove ground wire located on LH cowl side.
  13. Remove RH instrument panel upper moulding (04268) and LHinstrument panel moulding (04389) from instrument panel (04320) by pulling away from instrument panel and snapping out of retainers. Disconnect wiring connectors as required.
  14. Remove glove compartment (06010) as described.
  15. Remove two screws from center instrument panel support bracket at left side of glove compartment opening.
  16. Remove instrument panel upper finish panel (044A90) and disconnect the A/C sunload sensor (19E663) if equipped.

    Instrument Panel Finish Panels


    Item Part Number Description 1 044A90 Instrument Panel Upper Finish Panel 2 04320 Instrument Panel 3 04268 Instrument Panel Upper Moulding, RH 4 06081 Glove Compartment Lock Set 5 061A40 Glove Compartment Door Cover 6 N807122-S411 Screw (2 Req'd) 7 N807122-S411 Screw (10 Req'd) 8 - Parking Brake Release Handle (Part of 2780) 9 04459 Instrument Panel Steering Column Cover 10 04502 Instrument Panel Steering Column Opening Cover Reinforcement 11 04389 Instrument Panel Moulding, LH 12 044D71 Instrument Panel Cluster Finish Panel A - Tighten to 2.1-2.9 Nm (19-25 Lb-In) B - Tighten to 4-6 Nm (36-53 Lb-In)
  17. Remove five screws retaining instrument panel.

    Instrument Panel


    Item Part Number Description 1 N802539-S100 Nut (5 Req'd) 2 383554-S100 Rivet (2 Req'd) 3 01631 Vehicle Identification Plate 4 01544 Brake Pedal Support 5 N805632-S36 Bolt 6 N800854-S2 J Nut (2 Req'd) 7 N806030 Stud 8 N602480-S55 Nut 9 04320 Instrument Panel 10 N807122-S411 Screw (5 Req'd) 11 - Steering Column Retaining Nut 12 - Bolt (Part of 3F659) 13 3F659 Brake Pedal Support Steering Column Brace 14 N606675-S2 Bolt (3 Req'd) 15 04502 Instrument Panel Steering Column Opening Cover Reinforcement 16 N806067-S2 Bolt (2 Req'd) 17 N620482-S36 Nut 18 N801366-S2 Stud 19 045D56 Instrument Panel Cowl Brace 20 N606115-S100 Bolt (3 Req'd) A - Tighten to 9-14 Nm (80-123 Lb-In) B - Tighten to 10-14 Nm (89-123 Lb-In) C - Tighten to 2-3 Nm (18-26 Lb-In) D - Tighten to 47-63 Nm (35-46 Lb-Ft) E - Tighten to 45-70 Nm (34-51 Lb-Ft) F - Tighten to 22-34 Nm (17-25 Lb-Ft)
  18. Disconnect automatic temperature control sensor hose and elbow (19D888) from evaporator housing, if equipped.
  19. Disconnect vacuum hose harness assembly.
  20. On left side of engine compartment, disconnect all connectors and push harness through bulkhead.
  21. NOTE: The following steps should be performed be two technicians.

    Remove one nut and one bolt retaining left side of instrument panel finish panel (044D70) to cowl panel. Remove one nut retaining right side of instrument panel to cowl panel.
  22. Remove instrument panel finish panel from vehicle.

Jan 11, 2011 | 1997 Mercury Grand Marquis

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.

  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

Need to remove the dash on a 1998 lincoln town car to replace heater cord

Removal & Installation

  1. If equipped, turn the air suspension service switch to the OFF position before raising the vehicle.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Front seats
    • Carpeting
    • Rear airflow duct
    • Heater hoses
    1. Remove the driver’s side air bag module by removing or disconnect the following:
    2. SRS module-to-steering wheel bolts, from both sides of the steering wheel.
    • SRS module and disconnect the electrical connector
    • Horn switch electrical connector
    1. Remove the passenger’s side SRS module by removing or disconnecting the following:
    2. Open the glove box and disconnect the glove compartment isolator
    • Push inward on the 2 glove box door tabs and lower it
    • SRS module’s electrical connector
    • SRS module-to-instrument panel bolts and the module
    1. Remove the instrument panel by removing or disconnecting the following:
    2. Speed control servo nuts and move the servo aside
    • Bolt and disconnect the left side bulkhead connector
    • Left side bulkhead connector from the dash panel
    • Windshield washer fluid reservoir screw, and position the reservoir aside
    • Blower motor electrical connector
    • Air conditioning pressure cut-off switch electrical connector
    • In-line electrical harness connector
    • Electronic Automatic Temperature Control (EATC) variable blower motor controller electrical connector
    • Right front wheel
    • Right front fender splash shield bolts and move the shield away from the cowl
    • Wiring harness from the evaporator case
    • Wiring harness from the cowl
    • Right side instrument panel lower insulator pushpins, disconnect the power point electrical connector, remove the courtesy lamp from the socket and remove the insulator
    • Unseat the wiring grommet and feed the wiring harness through the cowl
    • Cowl side trim panels and the windshield side garnish moldings from both sides
    • Locking clip and the Electronic Crash Sensor (ECS) module electrical connector
    • Antenna connector
    • Ground wire bolts from the right side
    • EATC hose at the evaporator housing
    • Bolt and disconnect the bulkhead connector from the right side
    • Pull the door weatherstrip seals away from the instrument panel on both sides
    • Tunnel brace trim cover
    • Climate control head vacuum harness connector
    • Instrument panel tunnel brace nuts and the brace
    • Ground wire bolts from the left side
    • Wiring harness connectors from the left side
    • Parking brake switch electrical connector
    • Pry out the instrument panel defroster opening grille, disconnect the electrical connectors and the remove the grille.
    1. Remove or disconnect the following:
    2. 3 upper instrument panel screws
    • Instrument panel cowl side nut from both sides
    • Instrument panel cowl side bolt. From the left side
    • Instrument panel
    • Windshield wiper mounting arm and the pivot shaft
    • Electrical connector and remove the upper cowl extension screw and the extension
    • Vacuum hoses and the wire harness connector from the evaporative emissions canister purge valve
    • Evaporative emissions purge valve nuts and the valve
    • Cowl side nut
    • Right side rear fender apron screws and reposition the apron
    • Evaporator housing nut and screw
    • Vacuum hoses and the wiring harness connectors
    • Plenum chamber’s lower flange nuts
    • Plenum chamber’s upper flange nut and the plenum chamber
    • Heater core cover-to-heater plenum chamber screws and the cover
    • Seal and the heater core
  • May 26, 2010 | 2000 Lincoln Town Car

    1 Answer

    How you take off the front bumber

    have 96, 95 similar

    Section 01-19: Bumpers 1996 Villager Workshop Manual
    REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
    1. Raise and support the vehicle.
    1. Remove the RH and LH front wheel (1007).
    1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).

    1. Remove the four front fender brace screws.

    1. Remove the two front fender brace nuts.
    1. Remove the two plastic screws.
    1. Remove the seven clip buttons located under the front bumper cover (17D957).

    1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
    1. Remove the four front bumper cover brace bolts.

    1. Remove the front bumper cover from the vehicle.

    1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).

    2. Remove the eight front bumper bolts.

    1. Remove the front bumper from the vehicle.

    Mar 02, 2010 | 1995 Mercury Villager

    2 Answers

    My antena wont go down ,and the motor wont go off , even when the car is shut off .

    Unplug the harness to the ant.It will not go off,until you replace the whole ant.mass.The gear(plastic)are stripped out,and the motor can not sense that the moving.

    Jan 19, 2010 | 1991 Oldsmobile Eighty Eight

    3 Answers

    Replace front fenders 1999 wrangler

    Take off the tyre and remove the plastic inner fender first.

    Mar 17, 2009 | 1999 Jeep Wrangler

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    853 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides