Question about 1980 Chevrolet Corvette

1 Answer

How to install a door glass for a Chev C10 . I am have problems install the glass at the Drivers door. I need some help. As soon as possible

Posted by on

  • 2 more comments 
  • trevormottle Oct 06, 2009

    I am having problem get in Glass on the regulatory

  • trevormottle Oct 06, 2009

    No. It is a Chev C10 Truck

  • yadayada
    yadayada May 11, 2010

    why is it listed as a corvette?

  • yadayada
    yadayada May 11, 2010

    this is a corvette then?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

GM Full-Size Trucks 1980-1987 Repair Guide

REMOVAL & INSTALLATION
(see Figures 1 and 2)

Non-Stationary Door Glass

  1. Lower the door glass completely.
  2. Remove the trim panel from the door.
  3. Remove the ventilator assembly as previously outlined.
  4. Slide the glass forward until the front roller is in line with the notch in the sash channel.
  5. Push window forward and tilt the front portion of window up until rear roller is disengaged.
  6. Put window assembly in normal position (level) and raise straight up and out.
  7. Installation is the reverse of removal.
How to install a door glass for a Chev C10 - 4faff09.jpg

Fig. 1: Door window and regulator

0c5eed4.jpg


Fig. 2: Removing the door glass

Manual Door Window Regulator
(see Figure 3)
  1. Raise the glass to the full up position and tape it to the door frame with fabric tape.
  2. Remove the door trim panel.
  3. Remove the regulator to door panel attaching bolts.
  4. Slide the regulator assembly rearward, disengaging the rollers from the sash panel.
A notch is provided in the sash panel to allow disengagement of the forward roller on the window regulator.
  1. Collapse and remove the regulator assembly through the access hole in the door.
To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Collapse the regulator and insert it through the access hole in the door.
  3. Unfold the regulator and engage the forward roller to the sash cannel at sash channel notch.
  4. Slide the regulator rearward to engage the rear roller to the sash channel. Also engage the lower roller to the regulator rail.
  5. Slide the regulator into its proper position, and insert the regulator drive through the door panel.
  6. Attach the regulator to the door.
  7. Install the door trim How to install a door glass for a Chev C10 - af77872.jpgn>
af77872.jpg

Fig. 3: Manual window regulator

PowerHow to install a door glass for a Chev C10 - aa9dd10.jpgulator and Motor
(see Figure 4)


aa9dd10.jpg
Fig. 4: Power window regulator and motor
  1. Raise the glass to the full up position and tape it to the door frame with fabric tape.
  2. Disconnect the negative battery cable.
  3. Remove the door trim panel.
  4. Remove the remote control bolts and lay the control aside for access.
  5. Remove the regulator to door panel attaching bolts.
  6. Disconnect the harness from the regulator.
  7. Slide the regulator assembly rearward, disengaging the rollers from the sash panel.
A notch is provided in the sash panel to allow disengagement of the forward roller on the window regulator.
  1. Remove the regulator assembly through the access hole in the door.
CAUTION Step 9 must be performed when the regulator is removed from the door. The regulator lift arms are under tension from the counterbalance spring and can cause serious injury if the motor is removed without locking the sector gear in position.
  1. Drill a hole through the regulator sector gear and back plate. DO NOT drill a hole closer than 1 /2 inch; to the edge of the sector gear or back plate. Install a pan head sheet metal tapping screw (No. 10-12× 3 /4 inch;) in the drilled hole to lock the sector gear in position.
  2. Remove the motor to regulator attaching screws and remove the motor from the regulator.
To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Install the motor to the regulator. Make sure the motor and sector gear teeth mesh properly before installing the retaining screws.
  3. Remove the screw locking the sector gear in the fixed position.
  4. Reposition the motor in the door and install the wiring connector.
  5. Attach the regulator to the door.

I really hope help you with this (remember rated this help) Good luck.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Chevy extended cab 1500 and the controls on my driver side door aren't working. The door is saying it ajar when it's closed. I can't roll the windows up or down. Is it the master switch?


How to fix the Chev power window door lock switch - YouTube

? 5:04
https://www.youtube.com/watch?v=XDKaDURD8Sc
Jul 13, 2013 - Uploaded by spelunkerd
How to fix the Chev power window door lock switch ..... Some time later my drivers side window stopped working in the down position. ... These intermittent electrical problems are frustrating,aren't they? .... How To Install Replace Door Locks Chevy GMC Truck Silverado Sierra Yukon Tahoe Suburban ...

Diagnose Power Door Locks Dont Work Properly - Auto ...

www.auto-repair-help.com/.../diagnose_power_door_locks_dont_work_...
An inoperative power door lock can be caused by the switch, solenoid, wiring problem or ... Hi, I have a 2005 Nissan Sentra and the power locks aren't working. .... Hi, mypassenger door locks/unlocks both doors but my driver side door works independently and .... I have a 1986 Chevy Silverado K10 with auto door locks.

SilveradoSierra.com • 2003 silverado no power in right door ...

www.silveradosierra.com/.../2003-silverado-no-power-in-right-door-t30...

Dec 26, 2015 | Cars & Trucks

1 Answer

Why dont i have no forward & no reverse in my th350 transmission i just put it in my 82 chev c10


Hi Loren, My name is Randy and I'm going to try and help you with your problem, But I will need some more information from you. First did you by chance not bolt the torque converter to the flexplate or flywheel? Next Linkage is it installed on the trans and working properly. And what was the reason for pulling the transmission in the first place? Please get back to me maybe we can get your problem solved Thanks Randy.

Dec 23, 2015 | 1983 Chevrolet C1500

1 Answer

1996 cadillac deville how to replace passenger front door glass


remove interior door panel inside you will see where it mounts to should be two to three bolts and possible a clip that holds it in place remove old glass and install new glass from top of door remount into window gear mechanisim

May 20, 2013 | Cars & Trucks

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

1 Answer

I need to replace the drivers side outside door handle on a Chev Z 71


YOU NEED TO TAKE THE INNER PANEL OFF THE DOOR AND THEN UNDO THE CLIPS OFF THE DOOR UNLATCH ROD AND THE DOOR UNLOCK KEY ROD. TAKE OFF THE TWO 10MM NUTS AND IT'S IN YOUR HAND. REVERSE TO INSTALL.

Sep 29, 2009 | 1998 Chevrolet K1500

1 Answer

How to install striker on door jam of 1985 C10


It unscrews counter clockwise. More common is the metal around the area fatigues and needs to be built up...

Sep 18, 2009 | 1985 Chevrolet Chevy

2 Answers

HAVING TO PUSH THE STICK SHIFT UPWARD 1981 chev c10 truck


if it is an automatic a lot of newer cars are made that way its a saftey feature

Jun 03, 2009 | 1995 Nissan Pickup

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

2 Answers

2000 chev 1/2 ton


Do not pry off main panel! It has built on tabs to hold it in place.
First ease the angular top front panel, switch rest and handle cover.
flat screw driver used carefully works fine. Unplug the switch wire connectors [3]. remove the 2 small screws. door light can be remove and disconnected as well. The door speaker plug can be done after with the main panel part way off.
Lift up on the main panel to remove. Wedge or tape the window glass to before removing the power window assembly.
remove 5 bolts on the actuator assem. Loosen the 2 bolts on the glass clamps.

May 29, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

2,738 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...