Question about 1983 Chevrolet Camaro

Open Question

A guide on installing a 1979 Camaro sub frame on a 1954 Chevrolet 4 door BelAir

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dgjtex
  • 405 Answers

SOURCE: I have a 1979 Chevrolet

Remove caliper and nut to axle should come of with a little help of a rubber hammer. Knock bolts out from the front and drive new ones in from the back. You can use a lugnut with the flat side down to help pull them in and a hammer to help. Hope this helps.

Posted on Dec 26, 2008

SOURCE: install seat belt through seat belt guide 1990 camaro

The new seat belt guides will have a **** in them that allows you to put the belt through it. If it's a used guide taken off another car it may not have the ****.

Posted on Apr 16, 2009

mrjfisher
  • 141 Answers

SOURCE: keep lossing power to windows and door locks on

Driver door in the jam there is a boot with wires in it.
take it a part & see if any wires are broken. ALL you need is a small pinch in the power wire to make things not work.
To repair wire cut wire at pinch. place shrink wrap on wire solder wire slide shrink wrap over repair and heat it.If boot is bad replace it.
Remove neg - cable before cutting wire.

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to lower front sub frame on 2002 mercury sable


support car place jack stands under sub frame. using an engine support to hold motor in place, disconnect anything that is attached to sub frame, ex: motor mounts. then unbolt sub frame bolts(4) and raise car to remove sub frame. note sub frame is heavy.

Jun 24, 2015 | Mercury Cars & Trucks

1 Answer

For Dennis Weid camaro brake problems


the rear slack adjusters might need setting how is the park/emergency pedal?

Sep 03, 2014 | 1979 Chevrolet Camaro

2 Answers

Taking a 93 camaro front clip and installing it on


That is not even close to just bolting right up.If you want a camaro clip in your old truck you should use a clip from a 70 to 81 camaro.The subframes come out easy and are a fairly easy weld in as they are close to the same width as your truck frame.If you are not a skilled welder or fabricator you should just rebuild your truck front end,as this is NOT a job for a novice mechanic.A 93 camaro does not have a removable subframe like an older camaro they just have an engine cradle type frame that bolts up into the camaro not a frame that will work in your truck.

Jul 04, 2010 | 1993 Chevrolet Camaro

1 Answer

I need to see how to change a window motor in a 1995 Chevy Camaro.


I'm sorry, can't contact with your chat request because I having other question open; I suggest check this proceduro for GM Camaro/Firebird 1993-1998 Repair Guide...

Window Regulator and Regulator Motor
REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Remove the door trim panel and inner panel water deflector.
  2. Raise the window to half-up position and hold in place by inserting a rubber wedge door stops at the front and rear of the window between window and inner panel.
  3. Remove the rear guide channel and inner panel cam channel.
  4. Punch out the center pins of the regulator rivets; then drill out the rivets using a 1 / 4 in. (6mm) bit.
  5. Move the regulator rearward and disconnect wire harness from the motor (if equipped). Disengage the roller on the regulator lift arm from glass sash channel.
  6. Remove the regulator through the rear access hole.
ebf548d.jpg

Fig. 1: Front door window regulator mounting

CAUTION If electric motor removal from the regulator is required, the sector gear must be locked in position. The regulator lift arm is under tension from the counterbalance spring and could cause personal injury if the sector gear is not locked in position.
  1. Drill a hole through the regulator sector gear and backplate and install a bolt and nut to lock the sector gear in position.
  2. Using a 3 / 16 in. (5mm) bit, drill out the motor attaching rivets and remove the motor from the regulator.
00f7a3c.jpg

Fig. 2: Locking the sector gear on the window regulator motor



To install:

  1. To install the motor to the regulator. Use a rivet tool, J-29022 or equivalent, and install 3 / 16 in. (5mm) rivets or 3 / 16 in. (5mm) nuts and bolts. Remove the bolt and nut used to secure the sector gear in position.
  2. Place the regulator through the rear access hole into the door inner panel. If the electric regulator is being installed, engage the wire connector to motor prior to installing the regulator to the inner panel.
  3. Locate the lift arm roller into the glass sash channel.
  4. Using rivet tool J-29022 or equivalent, rivet the regulator to the inner panel of the door using 1 / 4 in. (6mm) 1 / 2 in. (13mm) aluminum peel type rivets (part No. 9436175 or equivalent). If the rivet tool is not available, use the following nut and bolt method:
    1. Install U-clips on the regulator at the attaching locations. Be sure to install the clips with clinch nuts on the outboard side of the regulator.
    2. Locate the regulator in the door inner panel. If the electric regulator is being installed, connect the wire connector to the regulator motor.
    3. Locate the lift arm roller in the glass sash channel.
    4. Align the regulator with clinch nuts to holes in the inner panel.
    5. Attach the regulator (and motor) to the door inner panel with 1 / 4 -20 x 1 / 2 in. screws (part No. 9419723 or equivalent) into 1 / 4 in. (6mm) nuts with integral washers. Tighten the screw to 90-125 inch lbs. (10-14 Nm) torque.
  5. Install the inner panel cam channel and rear guide channel.
  6. Remove the rubber wedge door stops at the front and rear of the window between window and inner panel.
  7. Install the inner panel water deflector and the door trim panel.

Hope helps (remember rated this).

Jun 04, 2010 | 1995 Chevrolet Camaro

2 Answers

Looking to pull the engine out of 95 camaro 3.4 with manual tranny does it come out the bottom or the top?


You can pull that engine out of the top. It is easier to drop the engine cradle, remove the drive shaft firs, and wiring harness. There should be four bolts located on the cradle at four locations. Lower the cradle with 2 jacks one on each side, lift the car and slide cradle from under the car. i have done this with an Intrige and was easier than trying to pull from the top.

Jan 02, 2010 | 1995 Chevrolet Camaro

1 Answer

Install seat belt through seat belt guide 1990 camaro


The new seat belt guides will have a **** in them that allows you to put the belt through it. If it's a used guide taken off another car it may not have the ****.

Mar 16, 2009 | 1990 Chevrolet Camaro

1 Answer

Installing brake system 1979 Firebird Formula


There are clips welded to the subframe where the lines cross over (and on the diff axle tubes as well), look for them and let them guide the install of the new lines, I know this info 1st hand, had a 79 Trans Am

Dec 01, 2008 | 1979 Pontiac Firebird

1 Answer

1979 Pontiac Firebird Full Brake System Install


You can go to the internet and look up under classic car. You can order a book on everything & ever part that was made on these type of car.

Dec 01, 2008 | 1979 Pontiac Firebird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...