Question about 1999 Subaru Forester

Open Question

2000 Forester with ABS light on.I've heard that if you cross wires in a plug under dash the light will blink for the code.Question is which plug in and what wire colors to cross?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: Need a stereo wire color code for 2000 subaru outback limited

Car Radio Battery Constant 12v+ Wire: Blue/Yellow
Car Radio Accessory Switched 12v+ Wire: Yellow/Red
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Green
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Brown/White
Left Front Speaker Negative Wire (-): Green/Black
Right Front Speaker Positive Wire (+): Red/Yellow
Right Front Speaker Negative Wire (-): White/Black
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): White/Red
Left Rear Speaker Negative Wire (-): Red/Green
Right Rear Speaker Positive Wire (+): Blue/Green
Right Rear Speaker Negative Wire (-): Red
window.google_render_ad();

Posted on May 17, 2009

Ad
  • 117 Answers

SOURCE: wires pulled out of plug dont no place of wires in

going to have to do the trial and error thing for the power window. connect them, try the window, if its wired backwards reverse connection. sorry can't be more help. if you have access to a wiring diagram, that would be your only other way to go

good luck

Posted on Sep 28, 2009

  • 2 Answers

SOURCE: How to replace dash lights

Take a look here
http://www.scoobymods.com/sf5_dash_board_removal-t11750.html

Posted on Dec 04, 2009

  • 10 Answers

SOURCE: 2000 subaru forester ignition coil wiring

Are there any other possible problems, or you are just not receiving spark at all now?

The coilpack could be dead and just need replaced. If you have a voltmeter or a test light, check the wiring on both sides of the coilpack harness to make sure it is receiving power.
I don't believe Subaru used ignitors past '99, but if they did, your should be located on the firewall behind the throttle body. Make sure it's plugged in and receiving power.

Coil packs do go bad from time to time. I had to replace mine in my
'98 Impreza a while back.

Goodluck!

Posted on Mar 16, 2010

  • 510 Answers

SOURCE: the ABS light stays lit on my 2000 Subaru

ABS is anti lock braking system,which helps to stop car in various conditions.Wet/slippery etc
Sensors are located on all brakes
You need to go to your local auto electrician who will plug in scanner to locate fault

Posted on Jul 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Tcs,abs,brake lights


you have to have the trouble codes for the abs read. then you can procede to fix the problem.if you can't get axcess to a scanner there is a procedure to retrine flash codes.easier to have it read

Oct 20, 2012 | 2000 Honda Odyssey

1 Answer

Cross plugged batterie acura tsx 2006


You still need to check in the underhood fuse and the in dash fuse the under hood fuse are no 22,13 and 15 and 23. The in dash number are number 7 and 21.

Mar 06, 2012 | 2006 Acura TSX

1 Answer

My abs light is on and my brake light blinks when i start to drive. i have already replaced the abs module, what else could it be?


There may be another module have you replaced it under passanger side dash or on the fire wall under the hood lots of cars have to be reset by machine one of the two could be your problem you have to remember most cars now are all electronic hope this helped

Nov 07, 2011 | Cars & Trucks

1 Answer

The ABS light stays lit on my 2000 Subaru Forester. I have replaced front disc pads and rear shoes (drum brakes) appear to be in good shape. Master cylinder is ok and there are no fluid leaks anywhere....


ABS is anti lock braking system,which helps to stop car in various conditions.Wet/slippery etc
Sensors are located on all brakes
You need to go to your local auto electrician who will plug in scanner to locate fault

Jul 19, 2010 | 2000 Subaru Forester

2 Answers

I have the abs light on and a technitian wanted to plug up a computer to the car to see wich sensor it was but couldnt find the plug to plug in the computer


That model accord doesnt use a scanner to access the abs system, there is a check connector on the pass side under dash that has to be jumped out and the light on the dash will flash the code. I would find another shop that is familiar with your system.

Apr 26, 2010 | 1994 Honda Accord

1 Answer

Blinking Light low power on my Subaru 2000 Forester


I the light is blinking under strain then it sounds to me that the alternator is not producing enough voltage to feed the power to keep the battery fully charged

Jul 11, 2009 | 2000 Subaru Forester

1 Answer

Trac Off and ABS Lights came on, won't go off


trac control & abs light staying on in dash on pt cruiser 2001 limited
well had same problem with my pt cruiser 2001, firstly there is no need to plug in computer under the dash for pulling abs error codes,
because the problem can be the cracked abs ring on the drive shaft/cv joint,
turn your steering all the way to left and ask your colleague to see if behind the tyre the abs ring is broken or cracked,
it is circular like a bracelete with grooves, then turn the steering to the right and repeat the inpesction,
if the abs ring is cracked then look on ebay or web for pt cruiser abs ring or kia abs ring, should cost about £5-£10 each
and a garage could heat it up with gas and hammer it into the drive shaft/cv joint for you for about £20-£30,
takes about 30min to 45mins, make sure the garage dont heat the cv booth kit rubber next to the abs ring when heating it up.
i heard you can only buy abs ring for front wheels and its not available separately for rear wheels,
so for rear you may need to buy the whole part it comes on
the front abs rings are easily visible when you turn the wheel to one side, the rear ones may not be visible as i have not seen them
so if the abs ring are good then it wil probably be one of the wheel sensors, in this case you you may look for a garage who will hook up
the computer and pull the code for you, be carefull if the say there are no abs error codes it means the sensors are ok and most of it
there is no need to buy abs sensor for any wheel when there are no error codes
on pt cruiser you can pull engine error codes yourself without a computer, just do the key dance on the ignition,
turn key until dash lights come on then switch off and then again turn key until dash lights come on then swithch off,
then turn key for third time again until dash lights come on , you will see engine error codes displayed then says done,
if there are no error codes it will say done, howevere these are engine error codes only not abs error codes,
abs error codes are pulled using abs diagnostic tool
incase its a faulty wheel sensor, will cost £45 at dealer or £20 from scrap, then a garage can removed the tyre and plug out the old sensor cable
and replace it with a new one, one end is easy to plug in but the other end has to be pushed in at an angle,
its about 30min job and garage can charge £20 or so
my pt cruiser is back on the road with just one abs ring replaced and it all cost me £30 alltogether

Apr 11, 2009 | 2002 Chrysler PT Cruiser

2 Answers

Abs light on, cruise control and engine light 2007 subaru outback


55 EGR Temperature Sensor or Circuit

ABS light is nothing to do with code 55 separate fault circuits.

Under dash there are two wires with mini spades at the end, connect one of them to the single black multiplug in position 2. Thats RHS plug inlet when you hold plug with tab lock on top.
ABS sensor should then flash up error coded. Ignore code 11 thats a initial flash to let you nknow the difference between a fast and slow flash.

Let me know what code flashes up and I will tell you the symptom,

Dan

Jan 01, 2009 | 2002 Subaru Outback

Not finding what you are looking for?
1999 Subaru Forester Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...