Question about 2002 Ford F150 Regular Cab

2 Answers

Ford f150 2002 has no brake lights

I have changed the fuse, brake switch and bulbs still no brake lights. is their a relay somewhere

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

Yes there is. Above the brake pedal there is a switch tat turns the lights on when you press the pedal. It is tough to replace due to the lack o room to put your hands. but is an inexpensive part.

Posted on Oct 06, 2009

Testimonial: "i have already replaced that switch and still no lights, thanks though, i appreciate your time and help"

  • Chris Yelton Oct 06, 2009

    Did you use a test light or just look at it? One of the more effective tools in diagnosing an electrical problem like yours is a test light. The test light allows you to prove if electrical power is present in the circuit before replacing parts. With a test light, start at the fuse, then move to the stop light switch. The stop light switch should have electrical power to one terminal of the connector at all times. If not check wiring back to the fuse. When you push on the brake pedal a second and third terminal (if equipped with a third brake light) will have electrical power



    Many vehicle’s brake light circuits share the same wire as the turn signal. If this is true on your vehicle, turn the directional signals on. If they work on both sides on the rear of the vehicle then the wiring and bulbs to the back are good. If the stop light switch is good and the wiring to the rear is good then you likely have a bad directional switch. Why? because the brake light circuit travels through the turn signal switch.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 6 Answers

Make sure someone didn't put the wrong bulb in the socket, it should take a 3157, I have seen chevy's where you would hit the brakes with the key off and the brake lights work, and the instant the key was turned on and the day runners came on they wouldn't work, and all it turned out to be was someone put the wrong bulb in the brake-light socket. Other than the fuse, there are plug ins at the rear where the bed mounts to the frame, they feed out of the rear bed pillars directly under the tail lights, it is possible they could have been pulled loose by a trailer light harness, make sure the wires from the trailer light harness aren't shorting out. And check the brake pedal switch to make sure it isn't defective, new doesn't always mean good. Make sure there is power going to the brake pedal switch. If these things don't fix your problem you might have to get your multi meter out.

Posted on Dec 29, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 s-10 4.3vortec vin x no brake lights...all other lights work...bulbs ok...Is there another fuse somewhere besides 2 in fuse box? Brake switch ok also.


The only applicable fuse is 20A STOP HAZ FUSE 1. The STOP LAMP RELAY or the TURN-HAZARD SWITCH (multifunction switch) could be defective.

Jun 28, 2017 | Cars & Trucks

1 Answer

I have a 2005 ford explorer sport trac the brake lights and hazards,blinkers .i have changed the multi functional switch and relay switch still not working i have also checked bulbs and fuses


Check and clean the brake switch, look near the top of the brake pedal arm you will see a switch remove it, clean it, replace it. If issues are still there check your wiring for good connections, recheck fuses in car and under the hood.

Apr 18, 2017 | Ford Explorer Sport Trac Cars & Trucks

3 Answers

1999 ford expedition no brake light no turn signal


Sounds like your multifunction control switch needs replaced. Its location is on your steering colum.

9ad0f03f-26fd-405e-89cb-10b4ae059161.jpg

Feb 14, 2015 | 1999 Ford Expedition

1 Answer

No brake lights


If the fuses, bulbs, switch are good then its your wiring, you have a break somewhere, check the switch behind your brake pedal, make sure you have power to the light sockets and they are not burnt, my wife has a ford edge and burnt right rear socket and the light still worked, go figure, anyways good luck

Apr 04, 2014 | 2000 Ford Expedition

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

1 Answer

Brake lights on 1993 ford mustang doesnt work


Did you change the bulbs? It might also be bad wiring. You can check the wiring by using voltmeter connected to the brake light and then have someone depress the brake pedal. If there is not 12- 14 volts on the meter then you most likely have a loose or broken wire somewhere.

Sep 10, 2012 | 1993 Ford Mustang

2 Answers

Ford focus Brake Light Problem, The 2 side brake lights do not work and i have changed the bulbs, the one above the rear window works, A garage has advised me could be the brake light switch, Would this...


It does sound like brake light switch, some have separate circuits for 3rd brake light. One question for ya... do you have trailer hitch/wiring on the car. Sometimes trailer wiring will short out and give same symptoms.

Jan 04, 2011 | 2000 Ford Focus

2 Answers

1994 ford explorer both headlights went out all of a sudden changed switch checked fuses no power at bulb socket running lights still work im stuck


Find the headlight relay and swap it with another relay to see if the lights come back on. If they do, replace the relay with a new one.

Dec 29, 2010 | Ford Explorer Cars & Trucks

Not finding what you are looking for?
2002 Ford F150 Regular Cab Logo

1,034 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...