Question about 1991 GMC Sierra

1 Answer

My 1991 gmc sierra front side turning light bulb burnt out. I need to replace it. How do I replace it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 324 Answers

On the front turn signal cover there are 4 phillips head screws (1 on each corner) holding it onto the grill. Unscrew those 4 screws and pull the cover out some and you will see that there are 2 turn signal harness attached to the back of the lens. Push in the little plastic arm on the side of the harness and twist them to the right I think. This will unattach the harness from the back of the lens allowing you to pull it out. To get the bulb out of the harness, hold the harness and twist the bulb to the right or left and pull it out. On the bulb there is a little notch that will only allow you to turn it one way. Hope that helps.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 GMC Sierra with stop light problems. I have checked the fues and bulbs which are good and replace the stop light switch but still have not stop lights.


sounds like to me the bulb socket needs changed or bad ground .pull back the carpet along the back and look for ground contacts.there should be a place where they conect a few ground wires .

Aug 02, 2011 | 1991 GMC Sierra

1 Answer

How do we remove the small yellow side lens in front to replace the bulbs. "parking Lens."


you need to remove the front turn signal lens to gain access to the bulbs.4 screws

Feb 06, 2011 | 1997 GMC Sierra

2 Answers

1991 GMC Sierra K1500 stalls randomly and starts when it wants


A bad ignition module can give you fits!!!! Replace it even if it doesnt fix it! You will be glad you did! Most likely that is the problem ,however!

Mar 21, 2010 | 1991 GMC K1500

1 Answer

Turn signal bulbs, front & rear, blinking fast , 1998 GMC Sierra Short Bed


if one side is flashing faster than another then check the side that blinks fast because you have one of the bulb blown on that side

Mar 16, 2010 | 1998 GMC Sierra

1 Answer

How do I install a new rt rear turning signal light on a 1997 GMC Sierra 1500 short-bed offroad?


Lower tailgate remove two screws on side of light t15 torx or phillips remove light. middle bulb is signal.To remove bulb push release tang and turn left to remove. Good time to change all bulbs. Same on other side

Feb 05, 2010 | 1997 GMC Sierra

1 Answer

2005 Sierra - driver side headlight bulb replacement


On top of the head light housing there will be two little metal rods about 1/8" round. They wiil be on each side of the housing on the top.Turn these out twords the front of the truck and pull them up ,.Once you remove them you will be able to get to the bulb.Twist the socket and remove the bulb.Then remove the wire harness.When installing the new bulb remember not to touch the new bulb with your bare hands.I use a paper towl to intstall the new one.If you do tough it be sure and clean it before installing it.

Dec 18, 2009 | 2002 GMC Sierra 1500

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

Replace 2005 GMC Sierra Daytime Running Lights...


Open the hood, and in the top right and left corners of the primary headlamps you'll see two pins (L shaped) swing them out (towards the front of the truck) and lift out. This allows you to remove the upper headlamp assembly. You can then remove the lower assembly by pushing outwards on the plastic clip that is hooked into a metal clip. Once it's out you just turn the bulb to remove it.

It's much easier if you unhook the leads to the upper assembly's bulbes so you can set the whole thing aside.

Mar 30, 2009 | 2005 GMC Sierra

1 Answer

Left blinker


Have you Replaced the Bulbs on the Left Side???? There should be at Least one Bulb that is Burnt Out. Please Rate My Response! Thanks!

Feb 04, 2009 | 1989 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...