Question about 1995 Chrysler LeBaron

1 Answer

I have a vibration at all speeds on a 95 lebaron convert. At slow speeds it seems like the front end is going side to side. Brand new tires, cv axles, rack, tierods, front motor mount. The tranny mount is rusted in place and doesnt move side to side like it should could this be causing it? Also the balljoint grease fitting is loose so this means the ball joints are loose, could that be causing this issue? I am at wits end PLEASE help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Hi,
You know, for the expense of tires being eaten left and right and for also your safety... especially if your front end linkage is on the verge of failure, I would recommend taking the car to a good front end shop and getting it fixed properly. They will inspect and replace faulty parts, and align the front end for you... it'll drive like a dream and will be worth the money spent.
I hope this helps... Good luck!

Posted on Oct 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 cabrio trans axle repairs


check the abs rings are not touchin the sensor (buckled) IF you use replacement cv from other than a reputable joint rebuilder or new oem equipment the problem sounds like you haven't fixed the fault. clicking while turning at slow speeds relates to worn cv joints.

Jan 19, 2013 | 1995 Volkswagen Cabrio

1 Answer

Bad vibration on right front tire even after new tires


Does it feel like its coming from the front or a certain side in the front and can you feel it in the steering wheel or brake pedal.Is it only at certain speeds accelerating,braking,decelerating or is it constant.

Jul 16, 2012 | 2003 Kia Sedona

2 Answers

My 93 lebaron 4 door has a shake int the front end and all the ball joints, tie rod ends, control arm bushings, and cv shafts are tight.


Does it pull to one side? Could possible be warped rotors, or a bad caliper.

Does it shake all the time even when braking, or only when braking? High speed or low?

May 02, 2011 | 1993 Chrysler Lebaron

2 Answers

I have a 2005 Honda CRV and get an intermittent vibration in the front end when going anywhere from 35-49 mph. Usually on straight road. Lasts for say 10 seconds then stops. New tires. Alignment if...


best guess is to have the CV joints checked, make sure that the boots are good in the outside joints. but it could also be the inside joint just has to much wear. you are at the right mileage for either to be the problem, the next time you get the vibration put a little pressure on the steering wheel in one direction then the other and see if the vibration goes away if it does suspect the CV joints. and don't just replace the outside joint replace both half shafts. if the vibration does not change or go away when you put pressure on the steering wheel then suspect lower ball joints.

Feb 03, 2011 | 2001 Honda CR-V

1 Answer

My car vibrates before new tires and after


vibration can be anything from brake rotors warped ,hub wheel bearing,bad cv joints or suspension part going bad -does it vibrate at different speeds or slowing down or under braking where do u feel the vibration in front or towards the back or while turning .tires dont usually vibrate unless it has a bad belt[defect in tire ]

Sep 24, 2009 | 2002 Mitsubishi Lancer

1 Answer

Cadillac Deville 1996 front end waddles at slow speeds.


it sounds like you may have a bad set of wheel bearings on one side or the other.which would mean you have a bad cv joint or one that is going bad. you may want to try to figure out which side the wobble is on and inspect that side.i suspect its going to be the side where you had the problem with the tire.

Jan 11, 2009 | 1996 Cadillac DeVille

1 Answer

1988 Land cruiser front end vibration from wheels


change the swivel bearing each side you got 2bearing do prober adjustment.


good luck

Dec 31, 2008 | 1988 Toyota Land Cruiser

1 Answer

Front end vibration


It sounds as though your car has two seperate problems. The first problem with the vibration that goes away when you let off the gas pedal is caused by a bad INNER CV joint. It only vibrates when you are accelerating because that is when the joint is under stress. Your vehicle has two axles, each with an inner and an outer joint. My suggestion is to have a competent shop determine which is the bad side and replace the entire axle. The second vibration which occurs at any speed is most likely cause by either a bad tire, or a bent rim.

Jun 03, 2008 | 1998 Honda Civic

Not finding what you are looking for?
1995 Chrysler LeBaron Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...