Question about 1993 Ford Ranger SuperCab

Open Question

Change the front blinker light on 1993 ford ranger

I want to change the front blinker light on 1993 ford ranger how do you get to the bulb does the light cover pop off or do you have to get at it from behind

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

Ad

SOURCE: how to take off the cover to change the rear blinker lights

Inside the hatch behind the light clusters, you will find the retaining nuts.

Posted on Nov 30, 2008

  • 1986 Answers

SOURCE: 2000 ford windstar how to install front blinker

The entire headlamp housing assembly sits inside of a mounting bracket - this means it is very easy to fully release, and remove the headlamp to make bulb replacement much less *painful*!

There are 2 headlight retainer clips to find - they are:

1. black, upside-down L-shaped metal clips about 1/2 inch wide
2. located just behind the top edge of the headlamp glass, inside the engine compartment. (Do not confuse these with the two small lens clips)

Release by pulling the top towards you while pulling the clips upward. The headlamp assembly will now pull forward providing great access to the electrical connector and bulb retainer ring.

Posted on Oct 29, 2009

c17hydro
  • 2984 Answers

SOURCE: how to change the oil pump of a ford ranger 1993

You didn't post your engine size so please pick the one that works for you....I'll post them all separately:

2.3L Engine The oil pumps are not serviceable. If defective, they must be replaced.

  1. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly.
  2. Remove the oil pick-up and tube assembly from the pump.
  3. Remove the oil pump retainer bolts and remove the oil pump.
To install:
  1. Prime the oil pump with clean engine oil by filling either the inlet or outlet port with clean engine oil. Rotate the pump shaft to distribute the oil within the pump body.
  2. Install the pump and tighten the mounting bolts to 14-21 ft. lbs. (19-29 Nm)

WARNING Do not force the oil pump if it does not seat readily. The oil pump driveshaft may be misaligned with the distributor or shaft assembly. If the pump is tightened down with the driveshaft misaligned, damage to the pump could occur. To align, rotate the intermediate driveshaft into a new position.


  1. Install the oil pick-up and tube assembly to the pump. If there is a gasket between the pump and the pick-up, use a new gasket when installing.
  2. Install the oil pan as previously described.

e4df20b.gif

Posted on Jan 19, 2010

  • 226 Answers

SOURCE: 2007 Ford Edge: Rear Blinkers/Brake Lights out; Not bulbs or fuse

Sounds like you need bulbs on both rear side lights. Does the blinker flassh really fast?

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 ford ranger. when you turn on left turn signal front light burns steady and back light does't burn. tested for power and had power. bulb is good. right side works fine.


Although you say you tested it for power, and the bulb is good, I am almost certain it you change the bulb it will work. The one at the back. Take the one from the right side and try it in the left. Then you'll know. If there is still nothing and your test light shows power, it has to be a bad ground wire. If you have an aftermarket trailer plug on that thing, that will be another place to look.

Aug 18, 2013 | 1994 Ford Ranger Supercab

1 Answer

1993 ford ranger blinkers not working


first check fuse if fuse okay the turn signal lights dont work and flasher dont work problem could be faulty turn signal switch or faulty hazard flasher.which locate on fuse panel under instrument panel to the left of the steering column.

Nov 28, 2011 | 1993 Ford Ranger SuperCab

1 Answer

2002 Ford Ranger pickup. The signal lights blink real fast and it appears to be wired wrong. Where are the front signal lights located


The light bulbs may have the wrong part number bulb,check the parts store to see that this is the problem,the blinkers are in the front near the headlights.

Aug 15, 2010 | Ford Ranger Cars & Trucks

1 Answer

Changing out Front Blinker bulb


I didn't realize how simple it was:

take out the ONE screw in the blinker cover.
pull it from the connector.
twist out the black cover around the bulb.
twist out the bulb.
replace with new bulb and i think the rest is pretty obvious!

May 11, 2009 | 2002 Mitsubishi Eclipse

1 Answer

How to change blinker light bulb


94 ranger is all I have. Maybe similar

Parking, Turn and Front Side Marker Lamps, Ranger Removal and Installation
  1. Remove one nut that attaches the parking lamp to the opening panel in radiator grille .
  1. Pull parking lamp away from vehicle to disengage the two barbed retainers.
  1. Twist the lamp socket and remove from lamp. For installation, follow removal procedures in reverse order.

Mar 09, 2009 | 1991 Ford Ranger Supercab

2 Answers

When lights are on. Right blinker stays on sollid.


you need to change the bulb in either the front or back on the side thats not working

Jan 11, 2009 | 2002 Chevrolet Impala

1 Answer

How do i change front blinker bulb


On my 2002 there is about a 3 inch black rubber circle covering it that is directly behind the light bulb that is just removed and then you pull the light out and pop a new bulb in. You have to work a little blind and just feel for it. Hope that helps.

Sep 30, 2008 | 2001 Buick Century

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...