Question about 1991 Plymouth Acclaim

1 Answer

Whre is the power steering pump located? - 1991 Plymouth Acclaim

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Your engine belt drives this pump, along with some other of your engine components. You should be able to identify a cap on the power steering pump, which is used to check the power steering fluid level.
Hope this was helpful... Good luck!

Posted on Oct 06, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Were is power steering pump located at

It appears it is under the AC Compressor. Both appear to share a belf for their repsective pumping activities. It should be possible to locate by tracing the hoses from the Power Steering Fluid resevoir (where you add fluid) to the devices behind pullies under the the air filtration system
Perhaps this link will be helpful
Repair Guides Power Steering Pump Removal Installation AutoZone com

Apr 30, 2014 | 2011 Nissan Juke

1 Answer

How to install power sterring pump

first you need to remove power steering pump drive belt and fluid using a large syringe or siphon pump.then you need place drain pan under vechicle where power steering pump located,remove power steering return line and remove power steering pressure hose using a flare nut wrench,make sure drain pan catch power steering fluid. once you have the power steering pump return hose and pressure hose remove,then remove power steering pump mounting bolts then remove power steering pump.take old power steering pump and new power steering pump to machine shop or garage so they can transfer drive pulley from old power steering pump to the new pump,once you have new power steering pump ready to install be sure to buy new pressure hose o ring if equipped, you need to bleed power steering system once you have new pump in place with every thing back in place cant give you bleeding procedure you did not tell me vechicle type you working on.

Dec 09, 2011 | Cars & Trucks

1 Answer

Wheres power steering pump located on 1997 ford contour,the power steering stoped working


Mar 12, 2011 | Ford Contour Cars & Trucks

1 Answer

Locating the power steering pump

Depending on your engine will make a difference
Just follow the power steering lines that come from the steering rack & pinion to the pump

May 29, 2010 | 2001 Buick Regal

2 Answers

Location of the brake fluid input

the brake fluid resivoir is above the master cylinder on the firewall. so on the left side near the windshield. the power steering resivoir is closer to the front end and is distinguished by not being connected to the master cylinder..

Feb 08, 2010 | 1987 Mercedes-Benz 300-Class

1 Answer

Changing power steering pump

Power steering pump special tools

Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

1 Answer

Location of power steering pump

Usually they are located near or part of the power steering reservoir. Look for the cap to fill the power steering with fluid the pump should be underneath.

May 06, 2009 | 1998 Isuzu Rodeo

1 Answer

Power steering fluid leak

The power steering pump is one of the devices that the fan belts operate. Follow all of the belts and note the pullys they run over. One of these devices will have two hoses about 1" in diameter comming out of it. Typically this is also where you fill the fluid when it is low, but not always. If you fill the fluid at a container on the side of the engine compartment, it will have a hosee that runs down to this PS pump as well.
Check for wetness along the lines especially at the terminal end of each line whre they meet the pump and where they meet the power steering box or rack. You may have to get under the car for this. If your car has a steering rack (about 2 feet long and three iN in diameter, look for fluid leaking at either end of the rack You can but rebuilt racks and have them installed by most garages. If that is the case have it done byy a garage that also does front end alignments as some adjustment in this are my be required

Good Luck

Feb 09, 2009 | 1992 Nissan 300ZX

2 Answers

Audi power steering pump location

Before you replace the pump, check the filter located inside the oil tank. This filter cleans the oil before going to pump. REMEMBER that Audi uses a special oil!!! Not your normal power steering fluid! Mixing them could cause damage to the entire system!

Jan 02, 2009 | 1999 Audi A6

Not finding what you are looking for?
1991 Plymouth Acclaim Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides