Question about Peugeot Liberte

Open Question

Front passenger wheel binding on peugeot806, s reg, took it to garage and had new caliper pads and discs but th eproblem continued, took it back to the garage and they replace the A.B.S. valve unit and assured me it was this but the problem is still occurring. it oly starts after about 3 miles and is ok aftr cooling down

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2005 LR3, last night the front passenger wheel locked up on me. When I applied small pressure to the brake, it just locks up. I stop na dput the car in reverse and it unlocks. It may run 20 f


There is definitely something out of the ordinary going on. The brake calipers have two pistons on one side which means that the whole caliper has to be able to move axially as the brakes are applied to evenly clamp the two friction pads against the rotor. There are no springs to release the brake pads from the caliper.
Probably one of the pistons is stuck causing the assembly to bind until you reverse the rotor's motion which releases the binding force. It is probably the lower piston of the two that is binding because that is where any crud in the brake fluid tends to accumulate.
If you take off the caliper off, you may be able to loosen the stuck piston with a brake piston removal tool and bleed fresh fluid through the system.

Jan 31, 2015 | 2005 Land Rover LR3

1 Answer

Should piston go all the way back where it is flush with piston outer housing?


Measure the thickness of the disc. It could be thin enough with the worn bads that the piston is coming out so far that it is binding in the bore.

Apr 23, 2014 | 2003 Toyota Celica

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

1 Answer

Hi ! changed brake pads on my navara d40 ,opened brake reservoir,took wheel off,opened top nut ,caliper went back.Took out old pads pushed in piston with g clamp,drivers side perfect, I have a problem...


Sounds like you have a seized passenger side caliper assembly. May need to be replaced, in which case you are better off replacing both front calipers as a set.

Jul 27, 2017 | Nissan Cars & Trucks

1 Answer

Front disc brake installation


Brake discs with pads need to be changed both sides on the same axle. Slacken the lug nuts and then lift the corner of the car and remove the wheel. Put a screwdriver tip between the brake pad and the disc and twist until a couple of millimeters of gap has opened up, do this front and back of the disc. Now remove the two large caliper securing bolts and lift the caliper up. locate the caliper body so that its weight does not pull on the rubber brake hose ( piece of wire to hold it temporarily to the strut spring is good). The disc is located by a couple of small screws. Remove these and the disc will come off the wheel studs. Fit the new disc and reinstate by reversing the steps above. Note if you have pushed the pads back far enough when removing the calipers then the caliper should refit easily over the unworn and therefore fatter new disc even with new pads fitted. put a small dab of anti-seaze grease (CopperEaze or similar) on the back of each pad as this will prevent squeal. Tighten the caliper bolts thoroughly when reassembling. Remember to pump the brake peddle back to pressure to re-seat the new pads to discs before test driving. Now do the same to the other side. If you are new to this the fist wheel is a voyage of discovery and the second wheel will take a quarter of the time.

May 12, 2011 | 2004 Jaguar X-Type

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Toyota corolla ae110 brakes binding


Please DO NOT drive in with the vehicle in this condition!!!!
What you have going on is that the brake caliper (part that holds your brake pads) is bad and sticking. Just remove it, get a NEW one from any chain autoparts store,and replace it. You will have to get a new set of pads as well,as due to the binding, the ones on there now are trashed.

Again,PLEASE do NOT drive in this condition as yours and your fellow drivers ,as well as your passengers safety is at stake.

May 01, 2010 | 1996 Toyota Corolla

1 Answer

Brake pad replacement 1996 ford thunderbird front and rear disc


1. Raise and support the vehicle
2. Remove the desired wheel
3. Loosen/remove the two caliper retaining bolts.
4. Remove the caliper from the wheel
5. Using a C-clamp, depress the caliper piston until it's completely recessed.
6. Remove the old brake pads
7. Install the new brake bads on the caliper
8. Reinstall caliper on the disc
9. Reinstall/tighten the calpier bolts
10. Put the wheel back on
11. Lower the vehicle.

*** When you are getting set let the car roll a few revolutions of the wheel to keep the pads off the disc. It will make it easier to get the caliper off.

Nov 05, 2009 | Ford Thunderbird Cars & Trucks

1 Answer

How to change the front brake pads on a v reg clio


The Renault clio should be easy,.jack up one wheel and remove the wheel and see what if any special tools will be needed. most have two bolts that hold the caliper to the back plate. The caliper hold the pads. Some of thes bolts are Allen head, some are Torq head, all are metric. some are held in with clips, remove the retaining pins and pull the clips out and the caliper comes out the front. Press the piston back into the caliper, so the new pads will fit over the rotor.

Jul 30, 2009 | 2003 Renault 181

1 Answer

Hyundai coupe se 2ltr 2001 front wheel bearing ceased to brake disk


hiya this does sound iffy ? but b4 i comment /offer an opinion could you or your friend jack up the wheel in question that has had repair and look at how the brake disc is secured to the actual hub assy that wheel bearing is housed in ? also caliper? cracked?? is it now a new one? have never had problem renewing front or rear bearings in past using the correct tool/s a hydraulic press is the best method for removing excessive siezed components as for your friend now saying noise is from rear ? it may be pads worne or disc/s corrosion/scoured so investigate and update what you discover ? sounds like big hammer garage?

Oct 24, 2008 | 2001 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...