Question about 2002 Jeep Grand Cherokee

Open Question

Wont select 4th gear - 2002 Jeep Grand Cherokee

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2000 Renault scenic 1.6 16v and have a gear selection problem only for 4th gear all the other gears select and 4th gear selects very hard and then jumps out of gear straight away when selected.


Sounds like it has run low of transmission oil. You may be able to save it by draining the gear lube and refill with DELCO synthetic Automatic transmission fluid. Make sure level is correct. The 4th gear syncro is bad, but the Delco ATF will help.

Jun 05, 2017 | Renault Cars & Trucks

1 Answer

1998 slk 320 r170 kompressor auto just had a transmission fluid service but the gears are still not selecting properly sometimes wont go into 4 gear


I believe this is an electronic transmission and the gear selection is done by electric solenoids not by internal oil pressure sliding valves. I am not sure the exact solenoid for 4th gear, but a dealer can identify and fix for not much money, They do not have to remove the transmission to replace the solenoids. And if the one for 4th gear is sticking, the others are not far away from the same issue. Should have them all done.

Feb 26, 2015 | Mercedes-Benz Cars & Trucks

1 Answer

2000 silverado wont go into passing gear


Check the A and B shift solenoids in valve body. A combination of either solenoids on or off gives 4 speed selection. For instance all solenoids off gives 3rd gear for limp home. Sounds like 1 solenoid is off all the time for no 1st and 4th. Check solenoid chart to see which solenoid is on for 1st and 4th. That solenoid is either not turning on or a wiring connection between the transmission control module and that solenoid.

Jul 10, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

1992 s10 5 speed transmission which 4th gear only works


4th gear in a box is straight through from clutch to tail shaft. All other gears get the movement from the cluster shaft so if you have this problem I would be checking the oil for metal as there may be bearing failure on the shafts.

Apr 04, 2013 | 1992 Chevrolet S-10

1 Answer

Shifting gears wont go, it wont get in or fit right on the dot


? Que? Do you mean that it doesn't select or move freely? Gets too notchy maybe? Has this car done alot of miles? Or just a good lot of gear shifts? All Diahatsu and Yaris have horrible gear selections.. what you COULD do is strip down the gear shift, check the ball on the end of the shifter for scoring, put in a decent grease (into the ball reccess) or sometimes there is heavy wear on the metal part of the shifter, just above the ball, if so, weld back up or if no welder try chemical metal. This will also have the effect of a shorter gear change. ok?

Mar 04, 2013 | Daihatsu Cars & Trucks

1 Answer

My gearbox wont select 5th gear


my suzuki baleno 2001 mod manual has a problem with the gear box. i can go 1st,2nd and 5thgear but can not get in to 3rd and 4th gear...what do you think it could be? thanks my email is: meancutback@hotmail.com

Sep 23, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

Feels like it wont go into 4th gear. Does ok from


chec fluid level while car runnin-is it red-if gritty flush it-there r ajust u can do-chilton books in library explain-also scan car for bad codes because trans is electronic

Sep 01, 2009 | 2005 Honda Accord

1 Answer

2004 mazda3 wont shift into 4th gear


Sounds like it needs a transmission. Try JDMengines.com

Jul 06, 2009 | 2004 Mazda 6

1 Answer

The gear stick has no resistance, I can only select two gears and it feels like Im stirring porridge when I do try and select a gear.


i'm unfamilar with the exact car but it sounds like part of your gear selection linkage is broken. This would be the part that is used to select the gears you can't select. I have seen some cars that use two cables, one for 1st and 2nd gear and the second for 3rd and 4th gear. I have also seen cars that use metal rods from the shifter to the transmission much like the cable setup, one rod for 1st and 2nd gear and the other rod for 3th and 4th gear.

Hope this in some way helps.

Nov 12, 2008 | Peugeot 405 Cars & Trucks

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...