Question about 2001 Toyota Celica

1 Answer

I wanna know how to do, the headlight alignment for a 2001 toyota celica gt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuse box located,fuse for the power windows,2001 toyota celica gt.


Sharon, In the downloadable manual pg.226-228 for your car the fuses for power windows are shown to be, fuse 24 in engine compartment fuse box and fuse #39 in the instrument panel fuse box location. Check the attached link, manual, instruction and guide, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

2001 Toyota Celica Owner Manual JustGiveMeTheDamnManual com

Aug 20, 2016 | 2001 Toyota Celica

2 Answers

I have a 2001 toyota celica gt. both front headlights will not come on. the high beams work. the car was hit in the front. does the headlight circuit have a fuse or a relay and where is it located. i found...


Have you checked the light globes ? The globes have a filament for each of Low and High Beams and the Low Beam ones fail much sooner than the high. A bump as you describe may have been enough for the Low beam filaments to fail as the filaments get brittle through age.

Sep 07, 2010 | 2001 Toyota Celica

1 Answer

How do you replace the rear shocks in an 01 Toyota Celica gt


YOU HAVE TO REMOVE REAR SEAT CUSHION TO GET TO STRUT TOWERS.

Apr 18, 2010 | 2001 Toyota Celica

1 Answer

What is are the correct headlight alignment specs for a 2001?



Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Oct 20, 2009 | 2001 Toyota Celica

2 Answers

85 Toyota Celica GT Headlights problem


Bad headlight switch or relay, or shorted wire. I would check the relay first.

Feb 07, 2009 | 1985 Toyota Celica

1 Answer

Removal of headlight housing to replace lowbeam bulb.


found this online- haven't tried yet though--
How do you change a headlight bulb on a 2003 Toyota Celica GT? Under the plastic covering the headlight there is a lot of fog and condensation and I want to clean it off, so how do I take off the plastic that covers the headlight?
  • 9 months ago
Seem to be seal is wear off
already on the front cover
The way to open that
1. There is four screws at the back of
the headlights and unscrew them
2. Pull the headlight and dry it
by wiping or heat of the sun or
anything that can release the fog
3. Buy silicon and seal the headlight
gap with silicon and let it dry for a hour
This will help kept away fog
and condensation for sure

Aug 24, 2008 | 2003 Toyota Celica

Not finding what you are looking for?
2001 Toyota Celica Logo

474 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...