Question about 1996 Chrysler Sebring

1 Answer

Interior wiring in drivers door. Radio, mirror lights, dome light on console, trunk light, power door locks and electric mirror switches don't seem to work. I suspect a fuse, #4 20 amp. under the hood and possibly #5 10 amp. under the dash. But if I replace one or both and they blow out again, I would like to find a schematic for this problem. Can you tell me where I can see or get this schematic?

Posted by on

  • Tim Marx
    Tim Marx Jan 14, 2016

    1997 Chrysler Cirrus.....

    Keeps blowing radio/dome light (IOD) fuse, PROBLEM SOLVED!!!

    I found the short! FOR ALL of you who may find yourself in the same situation, the fix was a short inside the AC module below the radio. At the back of the AC control module, there are two connectors. Disconnect the smaller 9 pin connectors and that will do it! The short was on the circuit board that has the lights on it

    I have the BCM working again so you can read your trouble codes with OBD scanner too.

    Pain in the azz!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 733 Answers

Do you have an aftermarket stereo? if you do, unplug it and see how long the fuses last. check your lighter and make sure there are no foreing object in there that can cause a short. when you replace the fuses, take notice of which action causes the fuses to blow... for example, door lock unlock, are they still ok, door lock, lock..check again, mirror left, still ok, so forth and so on. take it one at a time and see which action causes them to blow. when they blow do it again to see if the same action that caused them to blow the first time did it again, then trace those wires. you probably have a bad relay somewhere.

Posted on Oct 06, 2009

  • Pablo Gonzalez Oct 06, 2009

    do you have an aftermarket stereo? if you do, unplug it and see how long the fuses last. check your lighter and make sure there are no foreing object in there that can cause a short. when you replace the fuses, take notice of which action causes the fuses to blow... for example, door lock unlock, are they still ok, door lock, lock..check again, mirror left, still ok, so forth and so on. take it one at a time and see which action causes them to blow. when they blow do it again to see if the same action that caused them to blow the first time did it again, then trace those wires. you probably have a bad relay somewhere.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost the fuse diagram for my dads 95 dodge grand caravan. Can anyone help me out with one?


#1: Panel Illumination
#2: Guages,Right High beam headlight and the high beam indicator
#3: Rear Wiper, Left headlight High Beam
#4: RH park, backup lights switch and relay,Speed porpotional steering module,power door lock switch illumination and daytime running lights(Canada)
#5: Power Door locks,Power Mirrors,vanity,dome,map,ignition and trunk lights,sunroof,radio,power antenna,body control module and power for the data link connector
#6:Heated mirrors,heated rear window indicator
#7: Instrument cluster illumination,park and tail lights
#8: Cigarette lighter,Radio Amp and horns
#9: Power door lock motors
#10: Not used
#11: Radio
#12:Left low beam head light
#13,14,15,16 not used
26153814-2qh1jtrzfrcszgktlooiom5o-3-0.jpg

Apr 05, 2016 | Dodge Cars & Trucks

1 Answer

No dash, radio or door activated interior lights. Checked fuses already


Dash lights (Gone?) - FSB Forums - FullSizeBronco.com

www.fullsizebronco.com/forum/21.../198643-dash-lights-gone.html
Sep 7, 2011 - Fully rotating the shaft counterclockwise past a notch activates theinterior lights within the vehicles. ... No aftermarket stereo, the dash lights stopped working, and my taillights ... 8 15 Courtesy/Dome/Cargo Lamps, Electric Outside Mirrors, ... 12 20 C.B. Power Door Locks, Electronic Shift Motor 4WD, Power ...

Radio died, remote system not working, door locks will not work ...

www.topix.com > Chrysler Sebring
Aug 13, 2008 - So what all is not working at this time is: Door locks (with remote it only ... My lights on the dash dim some times and if I hit a bump the radio goes off, ... All the fuses are good, but still no power to the radio, interior lights, push ...

2009 Chrysler Town and Country No Dash instrument cluster lights ...

forum.chryslerminivan.net/.../55281-2009-Chrysler-Town-and-Country-...

Jan 13, 2014 - 10 posts - ‎5 authors

Dec 21, 2015 | Cars & Trucks

2 Answers

My sister has a 2000 chevy cavalier b4 the door chime and the interior dome light worked now they both dont, we replaced the bulb and fuse to no avail and I have no clue what's wrong with the chime.


the chime actually is done with the radio. the front drivers door speaker. so if the radio works and the front left speaker works. then more then likely you have a defective door switch. located in the door jam that controls the dome light

Apr 20, 2015 | 2000 Chevrolet Cavalier

1 Answer

Electrical problems with a 2002 Satun SL 200, the electrical door locks dosn't work, the mirror adjustments dosn't work, the dome light dosn't work. The engine runs good. head lights work


check all your fuses in engine compartment and under dashboard engine check light comes on every 3000 miles for oil change reminder

Jul 23, 2012 | Cars & Trucks

2 Answers

How to disarm or reset an alarm system for a 1996 Jeep Cherokee?


Hope this helps:- Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm.
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm. Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehicles

Dec 18, 2010 | 1996 Jeep Grand Cherokee

2 Answers

I have a 2003 Astro - interior issues


I had the same problem and found that my sliding side door "closed" switch, which is small and round and in the door frame, was not being pushed open all the way when the door was closed! As soon as I put a credit card in the spot where the switch hits the door all the locks and lights worked again. So I just taped a washer to the door where the pin switch hits it for now. The computer thinks the door is still open and will not alow them to lock and the lights won't operate right either.

Aug 04, 2009 | 2003 Chevrolet Astro

1 Answer

Need brake circuit diagram for 1991 chrysler new yorker


Hi,
1991 Chrysler New Yorker Auto Security Wiring Diagram
Battery Constant 12v+ Positive Wire (+): Red and Pink
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Dark Blue
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Black/Orange
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Black/Yellow
Parking Light Positive Wire Location: In Drivers Kick Panel

Power Door Lock Positive Wire (+): Orange/White Or Orange/Violet
Power Door Lock Positive Wire Location: In Drivers Kick Panel

Power Door Unlock Positive Wire (+): Pink/Violet
Power Door Unlock Positive Wire Location: In Drivers Kick Panel

Door Trigger Negative Wire (-): Yellow
Door Trigger Negative Wire Location: In Drivers Kick Panel

Dome light Supervision Wire: Use Door Trigger (Requires Relay)
Dome light Supervision Wire Location: N/A

Trunk Release Positive Wire (+): Black/White (Requires Relay)
Trunk Release Positive Wire Location: At Trunk Release Switch

Horn Negative Wire (-): Black/Red
Horn Negative Wire Location: At Relay In Fuse box

Tachometer Wire Negative Wire (-): Black/Gray
Tachometer Wire Negative Wire Location: At Ignition Coil

Brake Light Positive Wire (+): White
Brake Light Positive Wire Location: At Switch above Brake Pedal

Factory Alarm Disarm Wire (-): Light Green/Orange
Factory Alarm Disarm Wire Location: In Drivers Kick Panel

Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A


Thank You for contacting Fixya.com

Aug 03, 2009 | 1991 Chrysler New Yorker

1 Answer

Dome Light (switched circuit now working) Shorted it out


Why didn't you hook into the entertainment system (radio ) ?
The one that turns on when the door opens is controlled by the BCM -body control module .You probably shorted out the transistor in side the BCM .
These lamps may be manually turned on by placing the interior lamp switch in the ON position, or by opening a door.
• The Dome Lamp
• The Rear Compartment Courtesy Lamp
• The Rear View Mirror Map Lights
The inadvertent power control circuit of the BCM supplies battery positive voltage to the dome lamp and the map lamps. When any door is opened, the door jamb switch contacts close providing a door open input to the BCM. The BCM then provides a ground to the interior lamps. The interior lamps receive a ground at G401 or G403.
If the driver inadvertently leaves any interior lamp on the BCM will turn it off after a 20 minute time-out.
The courtesy lamps will normally turn off using the theater dimming feature. The BCM provides a pulse width modulated ground to the interior lamps for the theater dimming feature. The courtesy lamps will also turn off immediately if a door lock command is received with all the doors closed, or if the ignition switch is turned to the ON position.

--------------------------------------------------------------------------------
Dome Lamps Inoperative
ematic Reference: Interior Lights Schematics
DEFINITION: Only the dome lamp is inoperative.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle
2
Place the instrument panel (I/P) dimmer switch in the DOME position.
Does the dome lamp illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Disconnect the dome lamp assembly.
Probe the courtesy lamp supply voltage circuit with a test lamp that is connected to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 6
4
Connect the test lamp between the courtesy lamp supply voltage circuit and the courtesy lamp low control circuit.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 7
5
Inspect for poor connections at the harness connector of the dome lamp assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 8
6
Repair an open, high resistance, or short to ground in the courtesy lamp supply voltage circuit. Refer to Circuit Testing and Wiring Repairs .
YES - Did you complete the repair?
NO - Go to Step 9
--
7
Repair an open or high resistance in the courtesy lamp low control circuit. Refer to Circuit Testing and Wiring Repairs .
YES - Did you complete the repair?
NO - Go to Step 9
--
8
Replace the dome lamp assembly. Refer to Dome Lamp Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
NO - Go to Step 3

Mar 21, 2017 | 2007 Saturn ION-2 Quad Coupe

Not finding what you are looking for?
1996 Chrysler Sebring Logo

417 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...