Question about 2002 Nissan Altima

Open Question

Just bought a 03 Altima 3.5 SE and noticed wiring going to the engine mounts and wanted to ask what kind of sensor it had inside and what it did? Thanks, Randy

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know how many O2 wires in Nissan Maxima 03 sE


They have four wires, two for the signal and two for the heater circuit.

Sep 21, 2016 | 2003 Nissan Maxima

1 Answer

03 nissan altima jerks when put in drive also while driving it jerks. Also makes squeeking noise on passenger side


This that would be the correct fix. The bad mounts can lead to axle shaft wear, and linkages etc. to bind up. Not good for the driveline either.

Jun 02, 2014 | Cars & Trucks

1 Answer

2005 Nissan Altima jerks on Drive or Reverse for a second when hot.


Check for loss engine motor mounts and transmission mount
Also check the air tube (TOP AND BOTTOM) for hairline crack.

A loss motor mount can cause excessive vibration and damage the air inlet tube.

Jan 15, 2014 | Cars & Trucks

1 Answer

Where is the crank position sensor located on a 2000 Altima 2.4


I changed one on a 03 sentra and it was under the car by the exhaust entering the crank case. You can not miss it because it is the only object with a wire that is mounted to your engine block. Crank sensors will be close to the crank and cam sensors are close to the cam. I hope that this info helps.

Aug 04, 2012 | 2000 Nissan Altima

1 Answer

Where is my crank sensor located on a 2000 Grand Voager se 3 lter


It will be near the crank,on the inside of the engine compartment,on the engines eight bank,on the firewall side,it goes inside the engine ,but mounts on the outside.

Jun 27, 2010 | Cars & Trucks

3 Answers

Crank position sensor for 2003 Nissan Altima


a crank position sensor , sends a signal to pcm about crankshaft position signal, the sensor controls spark timing and firing order. the signal is also used for pcm to detect a missfire!! it also sends this info to ignition module, any mechanic can replace a crankshaft sensor!! call a auto parts store and see if you can get one, the cost should be a lot less.

Sep 01, 2009 | 2005 Nissan Altima

1 Answer

How to replace the crankshaft sensor on 2003 Nissan Altima


The cam sensor is mounted in top of the engine on the right side of the engine where the tranny mounts. You have to remove the top cover of the engine to get to it. Remove the electrical connector from the sensor, there is a clip that holds the connector in place. Push down on the back of it and then pull back at the same time. Pull on the connector and not the wires, they are very small and will break. Remove the bolt holding the sensor. To remove the sensor by twisting and pull on it at the same time. Is the engine not running, why are you replacing the cam sensor?

Aug 06, 2009 | 2003 Nissan Altima

1 Answer

Engine speed signal circuit


i have replaced the speed sensor and my vehicle still does the same thing. the cruse control keeps kicking off by its self.this speed sensor ios located on the top of the transmission.

May 14, 2009 | 2003 Nissan Altima

1 Answer

03 altima gas pedal regulator switch


Not gas pedal regulator switch . It's 2003 Nissan Altima Accelerator Pedal position Sensor Has to do with the electronic throttle control .
2003 Nissan Altima Accelerator Pedal Sensor

May 07, 2017 | 2003 Nissan Altima

2 Answers

1997 Doge Intrepit jerking


car has longitude motor? check the engine mounts

Sep 16, 2008 | 1997 Dodge Intrepid

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...