Question about 2006 Chevrolet Trailblazer

1 Answer

Replace relay fuse for low beam head light need location of relay switch

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

The relay is located in the engine compartment fuse panel near the battery

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

Where is the headlamp relay on a 2007 saturn ion


Are both low beams an high beams not working ? What engine does your car have ? Low beam relay only on 2.2 L .
On vehicles with manual headlamps, the LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low beam lamps and high beam lamps at all times. The low beam and high beam circuits continue through the fuse block - under hood, through the body control module (BCM), and to the headlamp switch. The low beam or high beam circuit then, depending on the position of the dimmer switch, continues through the headlamp switch. When the headlamp switch is placed in the ON position, it provides a ground path for the low beam or high beam lamps through G203. The low beam and high beam circuits are monitored by the BCM.
Is there B+ voltage at the headlamp fuse's ? Power runs from fuse through the head lamps to the dimmer switch through the head lamp switch to ground when turned on . If there is B+ voltage at the fuse ,check for voltage at the headlamp switch .
The

Oct 16, 2016 | 2007 Saturn Ion

1 Answer

Were is headlight low beam relay


It is located in the under hood fuse/relay box . It's non -replaceable ,if bad whole fuse box has to be replaced ! The low beam headlamps may be turned ON in 3 different ways:
?€¢
When the headlamp switch in the HEAD position for normal operations


?€¢
When the headlamp switch is in the AUTO position, for automatic lamp control (ALC)


?€¢
When the headlamp switch is placed in the AUTO position, with the windshield wipers ON in daylight conditions, after a 6 second delay

Battery voltage is applied at all times to the coil and switch sides of the LOW BEAM PCB Relay located in the underhood fuse block. When the headlamp switch is placed in the HEAD position, ground from G202 is applied through headlamps ON switch signal circuit to the body control module (BCM), signaling the headlamps ON request. In response to this signal, the BCM applies ground through the headlamp low beam relay control circuit energizing the low beam relay. With the relay energized, battery voltage is applied through the switch side of the relay, the left and right low beam fuses, and the low beam supply voltage circuits illuminating the low beam headlamps. Ground for the left headlamp is provided at G101 and the right headlamp at G100.
Low Beam Relay Test

  1. Ignition OFF, disconnect the C2 harness connector at the underhood fuse block.
  2. Connect a test lamp between the control circuit terminal A5 and B+.
  3. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.


    ?‡'
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

  5. If all circuits test normal, replace the underhood fuse block.
  6. Ignition OFF, disconnect the harness connector at the inoperative low beam headlamp. Test for less than 5.0 ohms between the ground circuit terminal B and ground.
    ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

    Connect a test lamp between the supply voltage circuit terminal A and ground. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
    ?‡'
    If the test lamp is always ON, test the supply voltage circuit for a short to voltage. If the circuit tests normal, replace the underhood fuse block.


    ?‡'
    If the test lamp is always OFF, test the supply voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the underhood fuse block.

    If all circuits test normal, test or replace the low beam headlamp.

Jun 10, 2015 | 2006 Chevrolet Chevrolet Impala LS

1 Answer

Where is the low beam relay switch located


Replace any blown fuses, and check or replace the head light relay.

Aug 16, 2014 | 2000 Buick Century

2 Answers

My low beam headlights do not work as daytime running lights or manually with the headlight knob pulled out . The high beam headlights however do work if I have the knob pulled out all the way with the...


Check out your fuse associate with the low beam headlight, secondly there is a relay fuse under fuse rely box under the hoos. Locate this box, and locate the relay fuse associated to the low beam. You can rotate the relay with another relay of the same spec to see if the low beam lights are coming on. I would believe that it is a fuse that is blown, check your owners manaual on the location of the fuse box. Usually it's located in the driver side kick panel.

Jan 30, 2011 | 2001 Buick Regal

1 Answer

2005 Dodge caravan. The Headlights are not staying on. When we turn the switch, sometimes they come on, sometimes they do not. It's getting worse.


Hello, on the van you have a high beam fuse and relay. On the low beam you also have a fuse and relay. Check the fuse/relay panel for a blown fuse controlling the low beam lights. If you do not find a blown fuse have some one to turn the key on and turn on the high beam lights. During this time locate the low beam headlight relay and place your finger on top of relay, have the other person to switch from high beam to low beam lights. You should feel a click in the relay when they make the switch from high to low beam. If not replace the relay and the problem should go away. Hope this will help you.

Thanks

Aug 14, 2010 | 2005 Dodge Caravan

1 Answer

Fuse relay switch


Sounds like you need new head lights ....it's common for the high beams to work if the low beams went ...good luck ..let me know how you made out ...bye for now Joe

Jan 08, 2010 | 2003 Honda Odyssey

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

Low beam headlights don't work


https://s12.postimg.org/6o2zcv3hp/jetta_headlamps.jpg

Click on the link.
This is for 03 jetta gls
There are fuses for left and right low beams. Headlights on low beam, use a test light, see if voltage on fuse circuit? If no voltage that will lead us back to dimmer switch or problem with wiring circuit from dimmer switch.

May 26, 2017 | 2003 Volkswagen Jetta TDI

1 Answer

Turn head lights on every light works except low beams


thare is a high beam relay and a low beam relay in the fuse box find the low beam relay and replace it. if this dont work its probabley the switch

Dec 31, 2008 | 2003 Ford Taurus

Not finding what you are looking for?
2006 Chevrolet Trailblazer Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...