Question about 2006 Toyota RAV4

Open Question

How to remove the tail lamp lens? - 2006 Toyota RAV4

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove tail light lens on 2000 ford contour SE


Open the trunk. Pull back the trunk lining where it covers the tail light access inside the quarter panel. Remove the lamp sockets for the turn/stop and backup lights, and remove the screws that hold the lens in place. The lens will then pull out from the quarter panel. Installation is the reverse: make sure the rubber gasket is in place properly.

Jan 28, 2013 | 2000 Ford Contour

1 Answer

License plate bulb replacement on a 2002 Buick LeSabre I don't have screws holding the bulb assembly in place. It appears to be in place with tabs larger than the assembly holding the assembly in...


Hi, my name is John I will do my best to assist you.

The entire tail/backup lens assembly has to be removed from the trunk lid as shown in the drawing attached. There will most likely be some nut's or clip's on the assemblies mounting pins on the inside of the trunk lid.
  1. Disconnect the tail/back up lamp harness connector from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
  5. Installation is the reverse of removal.

tecnovative_128.gif
If you have more specific questions please post comments to this thread and I will endeavor to monitor new activity and respond as soon as possible. I recommend that you "bookmark", or "add to favorites" this page for your convenience.

Feb 15, 2011 | 2002 Buick LeSabre

1 Answer

How to i remove rear lens cover to change burned out light,2009 dodge avenger


Open Trunk, There Is Some Hardware Behind The Tail Lamp That You Need To Remove, an d Then the Tail Lamp Will Come Out !!

Jan 12, 2011 | 2009 Dodge Avenger

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

2 Answers

Having trouble fixing brake lights


Tail/Turn Signal Lamp Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Oct 13, 2010 | 1997 GMC Sierra

2 Answers

How do I replace a burned out backup light on a 1998 cheverolet silverado c-1500 pickup truck?


Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Jul 17, 2010 | 1998 Chevrolet C1500

1 Answer

How do you replacw a rear turnsignal bulb?


Open the trunk, pull back the carpet on the rear wall of the trunk behind the tail lights. If there is access to the bulb sockets, figure out which one lines up with the turn signal and turn it counter clockwise about a quarter turn then pull it out. the bulb will either pull straight out or turn quarter turn and pull out.

If there isn't access to the bulb sockets then there will be three or four nuts or wing nuts that hold the tail lamp assembly in. Remove them and the lens. Then remove the bulb from the tail lamp lens assembly.

Jun 05, 2010 | 2004 Chevrolet Cavalier

1 Answer

Rear tail light lens removal I need to replace the brake light bulb, but I do not see a way to remove the lens cover. I do not want to bust the one I have in order to fix the problem


Hello riggs791. My name is Roger and I will help you. Raise the lift gate. In the rain drip rail you will find two screws through the lens to the body. Remove the two screws. Carefully pull on the lens. What you are removing to get to the tail lamp bulb is the entire lamp. The front outside edge of the lens has two lock in clips. Once you have the lamp loose turn it over and unlock the socket and replace the light. Reverse to reinstall the lamp.
Should you need further help please just ask. Please rate the quality of your answer. This way we know the answer helped. Thank You for using Fix Ya. Roger

Sep 26, 2009 | 1999 Ford Explorer

1 Answer

How do you replace the brake light on a 1997 ford taurus


remove the trunk trim covering the tail lamp retainiing bolts .... remove bolts, remove tail lamp lens assembly...advise replace ALL the bulbs since your there, reverse steps to reinstall....not to tuff to do...hope this helps you...GL

Jul 06, 2009 | 1997 Ford Taurus

1 Answer

NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Jun 08, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
2006 Toyota RAV4 Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...