Question about 1994 Jeep Cherokee

1 Answer

Blower motor not working changed the blower motor resistor fan still not working what is my next step

Posted by on

  • Dale Burns Sr.
    Dale Burns Sr. May 11, 2010

    Next step is a heavy single wire from ground, chassis or battery to the frame (motor housing) of the blower. I assume you have power to both sides of the blower fuse?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 295 Answers

Make sure the switch isn't burned out. I have seen many switchs burn out literally which then takes the resistor out too.

Posted on Oct 05, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: blower not working in 2000

Wire is too small to handle the amps of the blower. See if wire is burnt.

Posted on Sep 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2012 jeep libery blower motor control processor location


Processor? This system consists of a control unit ( switch/selectors ) a blower motor resistor and a blower relay. If the blower fan is not working on all speeds, suspect a resistor ( common problem ). If the fan is inoperable, possible fan motor,fuse,relay,wiring and in some cases the resistor as well. The resistor is located under the passenger side dash area close to the heater motor. The wiring coming from the heater motor will plug into the resistor

Dec 26, 2015 | Jeep Cars & Trucks

2 Answers

2004 crown vic. only 63K miles on her. AC/heat fan was sporadically working, now its done. AC was nice and cold, working fine. Is the fan a hard replacement if I were to find one at a parts yard?


Try to check the power and ground on the blower fan. If you missing the ground on the blower fan connector than most likely it is the blower fan resistor (controller), it is located under the hood close to back firewall behind left cylinder head.

Aug 17, 2015 | 2004 Ford Crown Victoria

1 Answer

How to change fan blower motor 2004 chev Impala


The blower motor is located under the Dash on the passenger side. Simply unplug it and unbolt the mounting bolts. The one closest to the firewall may give you a bit of a hard time as the angle is a bit limiting. Does the blower work on any speed? Usually the resistor block goes bad and the blower motor will not work on any speed but high. The resistor block is located next to the motor and it's held in place by two bolts. Good luck!

Jul 08, 2012 | Cars & Trucks

1 Answer

Gmc 2500 truck work blower does not work at all


Check your fuses for the blower motor. If they are ok, it is probably the blower fan resistor which is located on or next to the blower fan assembly under the passenger side dash in the footwell. if resistor is bad, there will be no fan speeds. make sure you are getting power to fan motor, if power but fan does not work then its the fan. check fuses and fan resistor first. good-day !

Sep 28, 2011 | Cars & Trucks

1 Answer

Heat fan only works on hi


There are only a couple of things that could cause this issue, and I would start with the simplest thing first, and that is to check your fuse panel. Your blower will operate only on high because it is wired to do so on the number 4 setting as it bypasses the blower motor resistor. If the fuses are good, then the blower motor resistor is the next step, and this can be found close to the blower motor, as the blower motor, when on, cools the resistor, when the resistor gets old and to hot, it will blow, thus causing your fan to only work on high. If the resistor is good, then the last thing that you would check is the fan selector switch. I seriously doubt that it is the switch, it is usually the fuse, or the resistor.

Mar 22, 2011 | 1998 Ford F150 Regular Cab

2 Answers

How do you replace blower motor resistor on a 2004 Envoy? Front fan motor does not go on so I am assuming its the blower resistor.


Here is how to change the resistor- but also pay attention-
Did you also change the connector at the same time?
If you are changing the resistor due to overheating and melting of plastic, then you need to do the connector also, or else it will repeat fail in a very short time.

Here is a step-by-step check you can do to fix it. If you are onlygetting high speed (setting 5), then most likely you have a resistorproblem, or the wiring connector to the resistor is bad. The groundwire prong being bad is a possible cause.

Check this for step-by-step checks:

http://www.sparkys-answers.com/2008/07/2005-chevrolet-silverado-blower-inop.html

Sep 01, 2009 | 2004 GMC Envoy

2 Answers

VW Jetta GL 2000, AC - Heater Fan stopped


blower motor or resistor or the blower motor control switch.

Jun 01, 2009 | 1998 Volkswagen Jetta

1 Answer

2003 Ford Explorer Fan Blower Motor


Jeff, If I understand you correctly you say your blower motor only works on high? check your blower motor resistor, located next to blower motor. The resistor makes the other speeds availiable, high bypasses the resistor, let me know if that fixes you up

May 27, 2009 | 2003 Ford Explorer

1 Answer

1997 Malibu Heater problem


this is usually caused by the blower resistor. it is located under dash on pass side. up close to firewall by the blower motor. need to confirm power is not going to fan also if you have power and ground to fan it is bad fan motor. if not most likely a bad resistor

Dec 05, 2008 | 1997 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...