Question about 1992 Ford Mustang

1 Answer

Replace value covor gasket - 1992 Ford Mustang

Posted by on

  • yadayada
    yadayada May 11, 2010

    what engine

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

You will need to remove the upper plenium part of your fuel injection that will give you access to the covers just alittle extra info spend the extra money and buy the rubber gasket instead of cork its so much better and most have the metal rings where your bolts go which dont let you over tighten them good luck

Posted on Mar 10, 2010

  • pitstang Mar 10, 2010

    O ya and Im assuming it is a 5.0 :)

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just replaced intake manifold gaskets value cover gaskets and know I have no oil pressure but there is noise in values what could be the problem will not drive it and I'm loosening everything only have...


Sounds like you didn't get the manifold sealed correctly and the engine is sucking air in and not creating any internal suction, or the oil jackets are plugged with stuff, or gasket is covering oil jackets. Or the pump dried out and needs replaced. The valve noise is due to lack of pressure.

Jul 30, 2014 | Cars & Trucks

1 Answer

What is the torque settings for a mitsubishi colt hiline 2.0i cylinder head?


There is no torque value. Commonly, Head bolts are tightened and then removed in sequence as you step threw 3 values: 23/33/45 ft lbs then the final value is achieved by rotating the bolts 90 degrees so the final value is unknown.

You have to get either a hayes manual or follow a procedure online if you are replacing the head gasket. If you are not replacing the gasket do not "re-torque" the head bolts thinking that you can fix a head gasket leak.

Jul 29, 2014 | 2005 Mitsubishi Colt 1.1

1 Answer

I need to replace the value cover gasket i like to know about how much the repair charges may run to fix it ?


Gaskets are $37 at Auto Zone. It would take you 30 minutes max even if your not experienced. Very easy repair. But if you hire a shop to make this repair, anything over $50 would be a rip-off.

Oct 14, 2012 | 2005 Acura TL

1 Answer

Replacing value cover gasket


One gasket for each valve cover, you have 2 covers. Upper intake manifold must be removed to access rear valve cover and all wiring that is in the way.

Nov 20, 2011 | 1998 Ford Windstar

1 Answer

Where is the valve gasket located on a 1996 Saturn CR


Around the edge of the value cover. The value cover bolts to the engine head (top) and the gasket fastens between the cover and the heads, All the cover and gasket do is direct the oil on top the engine values to flow back down into the engine block after this been pumped on top of the value stems. Gasket breaks and you have oil around the engine an on the ground. Also smoke when your driving around.

Apr 01, 2011 | Saturn SC2 Cars & Trucks

1 Answer

Tappet cover leaking oil


Pull the value cover, remove the old gasket and replace with a new gasket. Then, reinstall value cover.

Jan 09, 2011 | 1999 Daewoo Lanos

1 Answer

I have a 1992 acura legend with a blown head gasket do you think it would be cheaper to replace the whole engine or replace the head gasket I would replace it try to the car has 184000 miles


http://www.kbb.com/KBB/UsedCars/1992_Acura_Legend.aspx
Here is the link to the Kelly Blue Book. Plug in your zip code, mileage, and condition to get the value of the car. After you find out the value, check the price for an engine rebuild or a low mileage replacement engine. You may be better off just trading it.

Dec 20, 2009 | Acura Legend Cars & Trucks

1 Answer

Leaks oil looks like from valve cover


You have to remove the spark plugs cables and remove the four nuts that you see when the cables are removed.

When the four nuts are removed, simply raise the valuve cover. When replacing the gasket, make sure you get the gromets as well. Those sometimes get worn or crack since they are more exposed than the value cover gasket. Make sure that you clean the cover from oil and replace the gasket with no use of silicon.

Good Luck.

Jul 20, 2008 | 1999 Toyota Camry

1 Answer

No start


When you change out the Distributor, you need to change out two other things as well. You need new spark plugs, and spark plug covors.

Jul 12, 2008 | 1993 Mazda MX-3

Not finding what you are looking for?
1992 Ford Mustang Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...