Question about 2001 Chevrolet Impala

1 Answer

How toreplace turn signal relay

How to replace turn signal relay

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 28 Answers

I find another web site that gave info for free

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a1997 Chevy 1500 and I am wondering were is the flasher relay at.


Most cars the flasher relays are up under the dash not far from the steering column. I had several makes of cars and they all were up there.

Jan 10, 2016 | Cars & Trucks

1 Answer

Where is the blinker relay in my 2011 Chevy Equinox.


PCB Relays
This vehicle is equipped with the following printed circuit board PCB mounted relays.
• High beam
• Low beam
• DRL
• Fog lamp
• Park lamp
• Stop lamp
• Horn relay
They are directly soldered to the underhood fuseblock circuit board. A failure of one of these relays will require the whole under hood fuse block to be replaced.

Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Vehicles are just not the same as they use to be. Electronics !!!!!

Sep 25, 2015 | 2011 Chevrolet Equinox

1 Answer

Turn signal relay by left foot needs replaced. I can't figure out why it won't pull out of the convenience center. Is there a retaining device I'm missing?


GM Turn Signal Problem Fix - Directional Relay Replacement

? 5:38
www.youtube.com/watch?v=y4QVUBVVVpI
May 3, 2014 - Uploaded by Steve O
GM Turn Signal Problem Fix - Directional Relay Replacement ....You will need to install resistors in series with the directional LEDs

Sep 22, 2015 | Cars & Trucks

1 Answer

2000 impala,emer. flasher and turn signal not working; have replaced turn signal switch


you may have a bad flasher relay. its also known as a hazard relay, or turn signal flasher.

Jul 18, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

1998 Dodge Durango flasher relays location


Turn on the Durango and check each of the four turn signals to make sure that the bulbs are not burned out. If you find one that has gone out, replace the bulb and retest the turn signals. When a bulb goes bad on this circuit, the resulting operation can mimic a bad flasher or one that is failing.

Locate the combination turn signal flasher and relay. It is on the left end of the driver's dash. Open the access door and view the collection of relays and fuses. At the left side of the mounting block is a larger flasher and relay. This is the combination turn signal flasher and relay.

Test the relay by placing you finger on the relay housing and activating the turn signal. If you have found the right one, you should feel a clicking as the turn signal blinks. Remove the relay, replace with the new relay and close the access door

.

Start the Durango and activate the turn signals to check that they each work. The light should turn on and should blink. Also, check the hazard lights to make sure they work.

Feb 11, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

Turn signal not working


Could be either the turn signal switch, or the turn signal relay. Start with checking the relay. A lot of times you can replace it with one of the other relays in your car for a quick check. If they work after you try this. Replace the relay. If not check the switch.

Good luck!

Aug 15, 2010 | 2003 Dodge Intrepid

1 Answer

Relay for turn signal buzzes when turned on


The only reason that a relay buzzes is it is getting either a poor ground or a lack of power,clean your body grounding points and make sure you have a full 12v supply to the relay.If you have low voltage to the relay check the fuse and clean off any corrosion,if not that replace the turn signal switch./

Dec 05, 2009 | 1995 Nissan Pathfinder

1 Answer

I can't locate the turn signal flasher


next step after replacing fuses is to check relays,receptacles themselves and bulbs youll need a multitester with dc volts setting
first remove relay and have them checked or check them your self by making sure power is coming out of relay wires once turn signal is active using multi tester at 20 dcv setting if power is coming out relay is good
then remove bulb from turn signal housing and test if power is coming into socket same setting if so replace bulbs

Feb 06, 2009 | 1997 Nissan Pathfinder

1 Answer

HOW DO I REPLACE MY TURN SIGNAL LIGHTS ON 2003 HYUNDAI TIBURON


I just found out today that it is a problem for alot of 2003 tiburons that the flasher relay for the turn signals will go out causing the turn signal lights to stay on even with the car off. The relays are internal and located on the circuit board of the BCM. In order to fix you will have to remove and disassemble the bcm circuit board from it's housing and resolder a new flasher relay. Haven't figured out where to get that flasher relay though.

Jan 19, 2009 | 2003 Hyundai Tiburon

2 Answers

Turn signal not flashing


Most likely cause is the flasher relay located under the drivers dash in the fuse panel. This relay is round and may be metal. Replace it with an electronic flasher relay. Pay the ten bucks and have trouble free service for a lifetime.....
Good Luck.
Philip

Jan 17, 2009 | 1996 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2001 Chevrolet Impala Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...