Question about 2005 Volkswagen Jetta

1 Answer

2005 jetta 2.5L the drivers door electronics are non functional. Window, door locks, mirror controls won't function. Checked fuses didn't see any blown. Airbag warning light also has come on. What could be the problems?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 104 Answers

Check the door wiring harness where it enters the a-pillar for damage and the connectors for corrosion.

Posted on Oct 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 le sabre, power windows, door locks, side mirrors, not working all of a sudden


All - driver - passenger - front an back ? Look for broken wires inside the rubber boot from the body to the door ,driver side !

Power Windows Operation
Power Windows
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
If the status information to permit window operation is correct, the DDM sends the command to the door module controlling the window to move the window as requested.
Windows Power and Ground
The windows are powered by discreet power and ground circuits. These circuits are in the same dedicated connector as the window motor drive circuits.

PWR/WDO 30 amp circuit breaker located in the rear fuse box ,DRVMDL fuse 10amp located in the same rear fuse box . This power the driver door module (computer )

The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted.
The exterior key cylinders are wired to either the DDM or the passenger door module (PDM), depending on the location of the key cylinder. The interior lock switches are wired to the driver door switch assembly (DDSA) and the PDM. The DDSA and the PDM send the lock switch requests to the DDM over the simple bus interface (SBI) serial data circuit. The DDM then sends the lock requests to the RIM over the Class 2 serial data circuits.
The door lock operation modes are controlled by the rear integration module (RIM). The RIM examines the requested function from the DDM, or the remote function actuator (RFA), as well as the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. The RIM determines if a locking function is permitted, and commands the DDM to perform the function permitted. The DDM then sends commands to the rest of the door modules via the SBI to implement the selected locking function.
All programmable modes of lock system operation are stored in the RIM. The RIM checks the lock function program selected against the lock requests, the transmission selection and ignition key switch condition to determine if the requested function is permitted. If the requested function is permitted, the RIM then commands the DDM to perform the lock function over the Class 2 serial data circuits. The DDM commands the individual door modules to perform the lock function over the SBI serial data circuit.


GOOD luck your going to need it !

Mar 13, 2017 | 2000 Buick LeSabre

1 Answer

How do i fix the driver side window switch


The thing to do first is have the vehicle hooked up to a professional grade scan tool an have it checked for DTC'S in the driver door module , an to see if the scan tool will talk with the module !
Then if no codes are present check for battery power an good grounds at the module ! You have to take the door panel off the door to get at the module . I have one of these modules out in my tool box , I got it at the auto salvage yard . $10.00
In order to control window operations, as well as other door functions, door modules must be powered up. Battery voltage is supplied by the rear fuse block, through separate circuits, to each door module. Each door module is separately grounded through a ground stake. Additionally, the door modules use these power and ground supplies to provide voltage and ground to their associated window switch, and to provide voltage and ground for door lock operations. The front door modules also use these power and ground supplies to power the window express up sensors, and for outside rearview mirror operation .

How to test computer controlled door locks

Apr 10, 2015 | 2004 Cadillac Deville

1 Answer

2002 VW Jetta GL - Window & Mirror Controls no longer functioning


Check the wire bundle coming in to the door at hinge side. It is a short or broken wire

May 17, 2014 | Volkswagen Jetta Cars & Trucks

1 Answer

Similar electrical issues with driver's side door controls. Power locks, power window, and power mirror on driver's side are not functioning. I can manually unlock the door, but the buttons on...


CHECK FUSES FOR POWER WINDOW,CHECK FUSE FOR POWER MIRROR AND CHECK FUSE FOR POWER DOOR LOCK.IF FUSE OKAY DOOR CONTROL MODULE FAULTY ITSELF.

Sep 11, 2011 | 2004 Saab 9-3

1 Answer

2005 colorado pulled fuse for power locks, to stop automatic locks. drivers window and door locks quit working. reinstalled fuse but didn"t start working again.????. fuse is ok drivers window and locks...


This is a common problem, there is either a pinched wire in the harness that is in the door jam or your fuse block is shot, there is a gm service bulletin out on this, I would call your local dealership to find out if it is covered.

Jan 30, 2010 | 2005 Chevrolet Colorado

1 Answer

1999 cadillac seville sts driver side master control pannel dead


The same circuit breaker feeds the driver door as well as the passengers doors . The wires inside the rubber boot from the body to the door are probably broke ,power or ground wire .Or the door module is bad . Are your familiar with electronic control modules ? The door functions ,windows , lock's , memory etc... are controlled by DDM - driver door module .
Door Control System Operation
This vehicle has five modules capable of performing door system control functions. Vehicle door system components (windows, locks, mirrors, etc.) are controlled directly by these modules. There is a door module located inside of each vehicle door:
• Driver Door Module
• Passenger Door Module
• LH Rear Door Module (LRDM)
• RH Rear Door Module (RRDM)
• LH Front Power Window Switch
Simple Bus Interface (SBI)
Each Door Module communicates with the other Door Modules on the SBI. The driver door module is the only Door Module that is capable of communicating over the Class 2 Data Line as well as the SBI.
Driver Door Module
The driver door module directly controls the LH Front door lock actuator, power window motor and the outside rear view mirror. The driver door module sends and receives messages received from the LH Front Power Window Switch to the passenger door module, LRDM and RRDM modules over the Simple Bus Interface (SBI) line. Also, the driver door module sends and receives message from other vehicle system modules via the Class 2 Data Line.
Pulling the door panel off an checking B+ voltage and ground for the module would be good for you to do , since you probably don't have a $6,000 factory Tech 2 scan tool to see if the DDM is communicating .
The driver door module has two main power feeds (high and low current), and two main grounds. The low power feed (battery 1) is used to provide power for the driver door module's logic and internal driver operation. The high power feed (battery 2) is used to provide power for systems that draw higher amounts of current (motors, lights, etc.). Operating current at the driver door module's battery should not exceed 3.0 amperes at battery 1, and 7.5 amperes (for 2 seconds) at battery 2 while the driver door module is awake, and 2.5 milliamps when the driver door module is asleep. For most driver door module functions, the driver door module will operate properly with a system voltage of 9.0-16.0 volts. If system voltages exceed 16.0 volts the driver door module will provide protection by disabling certain functions that may damage due to higher than normal system voltages.

What kind of manual do you have ? The info above is from a factory repair manual .
The fuse's ,circuit breaker for the door module are located in the rear fuse box , not under hood . PWR WDO circuit breaker 30 amp. , DRVMDL fuse 10 amp. The rear fuse box is located under the back seat . Watch this video ,different type vehicle but probably the same problem .
Dodge Grand Caravan No Power Window No Power Locks CAN Trouble

Jul 23, 2017 | 1999 Cadillac Seville

1 Answer

The window controls only work on the driver's window


if it is the only window that works at all, even from their direct switches, then the window lock is on, or the fuse or wiring is faulty for the window lock. first check the fuse for the window lock, then remove another doors window consoles on the door panel and check for power and ground.

Apr 13, 2009 | 2005 Scion xB

1 Answer

2006 Jetta TDI. Drivers door lock will not lock or open with remote, also no dinging sound when lights left on, drivers door does not show open on display, powe mirror not working on drivers door. I have...


I had what sounds like the same problem on a 2001 GTI VR6 and found that the solder joints on the driver's side door lock module were cracked. I removed the module and resoldered the joints. This corrected the remote functions, key in and lights on dinging and dome lights lighting when the door is opened. Still working on correcting the power mirrors but everything else is working again.

This URL has excellent instructions for removing the module. http://forums.vwvortex.com/zerothread?id=1015107

Jul 31, 2008 | 2005 Volkswagen GTI

Not finding what you are looking for?
2005 Volkswagen Jetta Logo

517 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...