Question about 2002 Toyota Celica

1 Answer

Remote key problem

My remote key just opens the door but not close on my celica. that was being after i change my battery.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

Come online and chat while I guide you through the procedure.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I get my key remote to lock/unlock my toyota rav4 2002 model? I changed the battery because I thought that was the problem but it is still not working. The red light on the remote comes on but then...


You will need to try reprogramming the remote 1st, below is the complete procedure. If the reprogram doesn't restore function then you will need the dealer to test the keyless entry system, you may have a bad module or remote (only applies if both remotes don't work).

Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Close the drivers door
D. Insert the key into ignition and leave it in ignition.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Aug 24, 2011 | 2002 Toyota RAV4

1 Answer

Remote key does not open /close door lock


Hi.
It seems that the remote key need a battery change. replace the batteri inside the remote key.

If this is not curing the problem you might be in the situation where the transmitter (remote key) or the receiver (car) is defect.
In this case you need help from Suzuki.

Good luck

Feb 27, 2011 | 2006 Suzuki Swift

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

1 Answer

Remote got wet in salt water. Had battery changed


Programming
When
Key added or replaced. System malfunction.
How
Driver's door open and key removed from ignition switch. Insert key into ignition switch, then remove it. Within 5 seconds: Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch. Close driver's door. Switch ignition ON and OFF once to program a new key code whilst retaining the original codes or twice to program a new key code whilst erasing the original codes. Remove key. System should now lock and unlock vehicle, once or twice depending which mode has been selected. Carry out the following button procedure within 40 seconds: Press key lock or unlock button once. Within 3 seconds: Press same key lock or unlock button once. System should now lock and unlock vehicle.
NOTE: If system locks and unlocks vehicle twice, programming procedure has not been completed. Repeat button procedure.
If required repeat button procedure to program remaining keys.
NOTE: To exit programming mode: Open driver's door. NOTE: A maximum of 4 keys can be programmed

This will work providing printed circuit is not damaged in remote

Jul 20, 2010 | 2004 Toyota Camry

1 Answer

2000 Celica GT - I can get into the programming mode just fine, but I have tried to program THREE separate remotes and none of them will program. They are used, so I am "rewriting" them, but they never...


I saw this on one of the toyota forums;
1) Getting a Replacement Remote

Look on ebay or google, make sure the remote has the following FCC-ID: bab237131-056

2) Installing the remote (credit to iPal)

1 open door, take key out...

2 insert and remove key from ignition 2 times

3 close and open driver's door 2 times

4 insert and remove key from ignition

5 close and open driver's door 2 times

6 insert key into ignition

7 close door

8 turn ignition from 'lock' to 'on' and back to 'lock'

if you do step #8

*1 time it's for add mode

*2 times for rewrite mode

*3 times for confirmation mode

*4 times for prohibition mode

9 remove key

10 then door lock will cycle 'lock' and 'unlock' a number of times
corresponding to your key cycles in step #8

11 press lock and unlock button together for 1 ~ 1.5 sec then release

12 then within 3 sec press lock button for 1 sec then release

13 if you did correctly door lock will cycle once...

if wrong, twice... then do it over...

Jan 27, 2010 | 2002 Toyota Celica

4 Answers

How to program the orginal remote camry key2003


I found this on the internet try it it MAY work.

Start with the key out of the ignition. Open the driver door (all other doors are closed). Driver door is unlocked (other doors don’t matter).


Perform these steps within 5 seconds
Insert the key into the ignition (don’t turn it)
Insert the key into the ignition (don’t turn it)


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition (don’t turn it) and pull it out.


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition and leave in the ignition.
Close the drivers door
Turn the ignition to ON (as far as you can go without cranking the engine), then back to off .
Remove the key from the ignition.


Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.


Perform these steps within 40 seconds
Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.


Open drivers door

Dec 18, 2009 | 2003 Toyota Camry

1 Answer

Neither of my keys unlock my car anymore, wondering why this is? it can't be that both batteries in the keys have died.


if its the remote plips you mean, then the car may need recoded to the plips if the car battery has been disconnected or changed recently.

Otherwise the keyblades should still open the doors, or the central locking controller is faulty.

Oct 24, 2009 | 2001 Toyota Celica

1 Answer

The battery in my key fob for my 2004 Mitsubishi Diamante went flat. How do I reset it now that I have replaced the battery?


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 20, 2009 | Mitsubishi Diamante Cars & Trucks

Not finding what you are looking for?
2002 Toyota Celica Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...