Question about 1997 Ford F150 Regular Cab

1 Answer

Keyless remote and door panel lock and unlock are are not working

I used to be able to press the close button on my keyless remote and the doors would lock and the park lights would flash, That doesn't work anymore. My door is ajar light is always on,on the dash. My radio used to shut off when I opened the door, that doesnt work anymore, I have to turn it off now. Fuses are all good, I have used wd-40 on all my door latches, blown it out with compressed air and used a spray grease on them. Occasionally the door panel switch will work all four door locks but not the keyless remote and that has abrand new battery. for some reason the truck thinks that a door is open when it is not. What can I do?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 424 Answers

At least one of your door ajar switches are sticking. If you have tried lubing them,then the switch needs to be replaced. This is causing most of your concerns. Try one door at a time to see if the light goes off. The most common switch is the driver's door.Good luck.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Ford 2010 Ford Explorer "Remote Keyless Entry (RKE) module" located


The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????
  • The doors do not lock/unlock using the remote keyless entry (RKE) transmitter
  • RKE transmitter battery
  • RKE transmitter
  • RKE transmitter programming
  • Aftermarket system
  • SJB
  • Go To Pinpoint Test H .

Apr 16, 2017 | Ford Cars & Trucks

1 Answer

How do i program keyless remote on 2004 navigator


1. Close all doors and then open drivers door and press the UNLOCK
button on drivers door panel while door is open and insert key in ignition.

2. Turn ignition from OFF to RUN 8 times within 10 seconds, with the
8th time ending in RUN. Door locks will cycle to confirm programming
mode.

3. Within 20 seconds press any button on first keyless remote.
Door locks will cycle to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
Door locks will cycle again to confirm programming.

5. Turn ignition to OFF.
Locks will again cycle to indicate end of programming mode.

Oct 13, 2012 | 2004 Lincoln Navigator

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

2 Answers

Programming instructions for keyless remote Does anyone have the programming instructions for 1998 honda passport keyless remote (FCC #HYQ1512R)?


Get into your passport and unlock all doors. Leave drivers door open. Put key into ignition. Turn to ON (not start), then OFF three times within 5 seconds. Close and open the drivers door twice. Turn key to ON then OFF 5 times within 5 seconds. Close then open the drivers door. Press either the lock or unlock button on the remote. Doors will lock then unlock. Press the button again. Doors will lock then unlock again. Close door to finish programming. If it doesnt work, try it again but turn the key faster. You have to do it all pretty quick, but I had it done on the second try.

Oct 03, 2009 | 1998 Honda Passport

1 Answer

Can't program Second remote to my Ford Explorer 99


reading your post you mention to "open and close switch"..not sure what refering to...these are the instructions from your vehicles service manual...good luck!

Programming NOTE: All keyless entry remote transmitters (15K601) are programmable and must be set at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Diagnosis and Testing.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 08, 2009 | 1993 Ford Explorer Limited

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

1999 lincoln con


SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------

Apr 07, 2009 | 1999 Lincoln Town Car

1 Answer

Keyless remote


Don't know for sure it will work with your but try this.

  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the door unlock switch.
  4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation.

Sep 25, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
1997 Ford F150 Regular Cab Logo

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...