Question about 2001 Ford Focus

Open Question

2008 ford focus throttle control/transmission warning light on car runs fine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2008 ford focus

Its 5W-20 oil for the ford focus

Posted on Sep 05, 2008

Ad
  • 88 Answers

SOURCE: ford focus ignition warning light

hi with the engine running at idle .get a multimeter and check for a voltage of between 13.5 volts and 14.7 at the battery terminals lower than 13.5 or higher than 14.7 replace alternator.

Posted on Oct 31, 2008

  • 7 Answers

SOURCE: 2005 DB9 / crank no start

pull out negative terminal battery located under rear right seat.wait for 5 min n then install again the lead negative terminal.insert the key to ignition cylinder.turn the key on off three times.now start the engine.make sure u use recommended fuel grade.

Posted on Jun 21, 2009

  • 1 Answer

SOURCE: Ford Focus 1600 Automatic.

Problem resolved by local garage.
Please do not send me any more e-mails
I do not want an account
Please remove my e-mail address from your records.

Thanks
J.Ball

Posted on Nov 02, 2009

honeymokey
  • 3113 Answers

SOURCE: 2003 Ford Focus ZTS. After running on the highway

Check for stuck throttle plate. Check pcv hose that goes to the intake manifold. They get soft and leak, check while running.

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Ford Focus automatic. Engine starts, shifter has no feel going through , and screen gives transmission malfunction warning. car has always run well transmission wise . Any suggestion appreciated


IF the warning light is on, then there's a trouble code stored in the computer. Get the trouble code read. That's always the starting point in any diagnosis.

Jun 28, 2017 | Ford Cars & Trucks

1 Answer

Why does a red light come up on the dash board saying a transmission malfunction on my focus 08


The light is on because something has malfunctioned in the transmission system, this can be a sensor or wiring or the transmission has a mechanical fault. The next step is to have a scanner hooked up and read the fault code that was set in the control modules memory when it turned on the warning light. This may require a trip to the local dealer.

Jan 06, 2017 | 2008 Ford Focus

1 Answer

2010 ford explorer wrench light what does this mean


Wrench Warning Indicator (Base Instrument Cluster)
The instrument cluster receives the powertrain status from the PCM over the HS-CAN. When a powertrain system concern is detected, the PCM sends the instrument cluster a command signal to illuminate the wrench warning indicator. If the 4WD control module detects a failure with the 4WD drive system, the 4WD control module sends a message to the instrument cluster over the CAN to illuminate the wrench warning indicator. On 4.6L engines, if the transmission control module (TCM) detects a failure with the transmission, the TCM sends a message to the instrument cluster over the CAN to illuminate the wrench warning indicator.
You need to take it to the dealer for them to sort it out , needs dealer IDS factory scan tool to see which system is the problem .
You

Dec 02, 2015 | 2010 Ford Explorer

1 Answer

How do i reset ABS and traction control warning lights on a 2008 ford focus


if there is light o the panel you may not reset it , you must go to scanner to detect which problems occurs on the abs ..

Feb 10, 2014 | 2009 Ford Focus

1 Answer

2008 ford focus surges


run fault codes to determine why the transmission is staying in gear and not down shifting as the speed slows. Check for TCM problem. If nothing shows then have a pressure test done to determine if there is a mechanical fault in the box

Jan 24, 2014 | 2008 Ford Focus SE Sedan

1 Answer

57 plate, Ford Focus Zetec, 1.8 diesal. ABS warning light,Steering Failure Assist light and Battery light on again. Alternator replaced 9 days ago, and been sluggish,heavy steering since and now won't...


2009 Ford Focus Zetec, 1.8 diesal. ABS warning light,Steering Failure Assist light and Battery light all on. Can't steer car. Then takes twenty minutes to restart car. Any ideas?

Dec 26, 2010 | 2008 Ford Focus

2 Answers

On a 2008 f550 after driving 10 to 15 km the dash warning lights come on the gauges jump around and there is no throttle response. After a minute or two it clears up and runs fine.


Check the alternator out put,if possible,check it when this occurs,out put at the battery when it is running,should be 13.65,to 14.25 volts.

Nov 20, 2009 | 2008 Ford F 450 Super Duty

1 Answer

Why does the wrench light on the dash board go on sometimes on my Ford Focus AWD


Throttle Control/Transmission:
Illuminates when a powertrain fault
has been detected. Contact your
authorized dealer as soon as
possible
This is from the owners manual

Jun 19, 2009 | 2008 Ford Focus

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...