Question about 2006 Honda Accord

1 Answer

How long should it take to replace a Honda Accord 2006 Master Cylinder?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

The hardest part is priming it with fresh brake fluid before you install it. Typically it takes about a half hour. I am curious on a 2006 it shouldnt need replaced and wouldnt it still be under warranty?

Posted on Oct 05, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to bleed clutch master cylinder on a 1995

It takes 2 people. Open the bleeder on the slave cylinder, hold your finger over it while the pedal is pumped, releasing the pressure when the pedal is down.. Once it starts pushing fluid thru, close the bleeder, pump 3 times, open bleeder with pedal down. Repeat till clutch feels good. If you are replacing the master cylinder, bench bleed it 1st. Be patient, this all takes awhile.

Sep 30, 2014 | 1995 Honda Accord

1 Answer

How to pre bleed the master cylinder on my 1996 honda accord 5 speed

there are different ways to bench bleed the master depending on the tools available to you... did you receive a fitting, with or without a port for a small hose, in the new master box? if not then you should make one or get one at the parts store. you need to put the master in a vice (from the mount, not the body) and fill it with fluid. this is where the fitting comes in handy, you are going slowly depress the piston about half way at first having the fluid that comes out the port directed back into the reservoir with a hose. keep the hose submerged. if a vice and fittings are not available, you can mount the master in the vehicle, connect the line and fill with fluid. disconnect the line from the slave cylinder and submerge it in a container. press the pedal by hand slowly. make sure the line stays submerged and the master is never run dry. if everything is kept clean, you can reuse the fluid from the catch container.

Apr 17, 2014 | 1996 Honda Accord

1 Answer

Fixing Clutch master cylinder in my honda accord 1998. The metal line wont fit into the new master cylinder....

I believe this is all about alignment. take a look at the old one, compare to the new one and make sure they are the same. If they are, then it is alignment. some times it helps to loosen the mounting bolts to get a little movement for alignment. best of luck.

Feb 12, 2013 | 1998 Honda Accord

1 Answer

I changed rear calipers on 94 Honda accord. Not getting fluid to one side now.

I was looking through your recent posts and i own a 95 honda accord and i had the same problem. thinking my brakes were bad and that my brake booster was bad. but just to find out my master cylinder was shot..
seems like you replaced your brakes for no reason as did i.
my master cylinder could have possibly went out. and could be a reason why no fluid is running on one side. hope this helps

Feb 05, 2013 | 1994 Honda Accord

1 Answer

Master cylinder

It's basically replacing the parts, unbolting and removing each part. You just want to make sure you have all the air out of the system.

May 04, 2010 | 1990 Honda Accord

1 Answer

Brake pressure

Inspect the master cylinder. The pedal may not be connected correctly or there are bad seals that is causing you to loose pressure resulting in no resistance. In some cases you may see leaks.

Feb 18, 2010 | 1991 Honda Accord

1 Answer

1997 Honda Accord ABS makes a "grinding" noise when turned on

Have you had the master cylinders replaced? Mine made this exact noise and they replaced the master cylinder.

May 11, 2017 | 1997 Honda Accord

1 Answer

What engine type do i have?

You have a timing chain not a belt. Happy motoring.

Nov 03, 2008 | 2006 Honda Accord

1 Answer


take the top off the master cylinder and while someone is pushing the break pedal down, looks for bubbles coming up in the master. Master cylinder probably needs rebuilding or replacing.

Jun 26, 2008 | 1995 Honda Accord

Not finding what you are looking for?
2006 Honda Accord Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides