Question about 1994 Isuzu Trooper

1 Answer

Cylinderhead bolts torque settings - 1994 Isuzu Trooper

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Its tighten to this amount then by angle

25. Cylinder Head W/intake Manifold
· Clean up cylinder head lower surface and cylinder
body upper surface.
· Install cylinder head as softly.
· Apply engine oil to screw and seat of cylinder
head bolts.
· Tighten cylinder head bolts in following sequence
1st Step

36 Lbs /ft
2nd Step
60° - 1/3 a of a turn
3rd Step
60° -- same

And thats in a spiral out from the center .

Posted on Oct 05, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: Cylinderhead bolts torque settings

According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need the cylinderhead torque settings as well as the timing marks for the Nissan UD40 FD46 motor. can you possibly assist? Thanks


1. 29 nm
2. 59 nm
3. slacken off bolts
4. 29 nm
5. 50-55 degrees with angle torque gauge or 54-64nm
10_3_2016_6_03_48_pm.jpg

Oct 03, 2016 | Nissan Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Hiya do you know the torque settings for cylinderhead for a bmw 525d e39 2002, 6 cylinder


Per BMW AG,
Jointing torque: 80 Nm
Loosen all bolts 1/2 turn
Jointing torque 50 Nm

http://www.adrianteo.com/files/cylinder-head-torque.pdf

Oct 05, 2014 | Cars & Trucks

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

1 Answer

CYLINDERHEAD BOLTS TORQUE SEQUENCE HYUNDAI ELANTRA


Install the gasket so that the surface with the identification mark faces toward the cylinder head.
Tighten the bolts to the specified torque in the sequence shown below.
b176b2ac-2453-4b5b-9b1d-0cb775cacffe.jpg

Aug 04, 2014 | 2001 Hyundai Elantra

1 Answer

What is cylinderhead bolts torque settings


follow this link and click on torque tables then look up your vehicle
http://www.speedwayautoparts.com/index35.htm

Jul 22, 2014 | Nissan Sentra Cars & Trucks

1 Answer

REPLACING CYLINDERHEAD-TORQU SPEXS NEEDED


For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of theconnecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90 more
4. Check that the crankshaft turns smoothly.

Sep 11, 2012 | Cars & Trucks

1 Answer

Cylinderhead bolts torque settings


According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.

Nov 29, 2008 | 1994 Land Rover Discovery

1 Answer

Hi I ned to know about head bolt torque nissan sentra 1997


hi.im a mechanic from the philippines.the torque of all your cylinder head for your nissan sentra 1997 is 60 nm.apply 30 nm of torque first on all the cylinderhead bolts then torque it agian directly to 60 nm. i also drive and repair nissan cars.

Aug 07, 2008 | 1989 Nissan Sentra 4 Door

Not finding what you are looking for?
1994 Isuzu Trooper Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...