Question about 2000 Hyundai Elantra

1 Answer

Do you have to remove the yoke to change the water pump and if so is the bolt l. or rt. hand threaded

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

There is NO yoke. There is, however, a water pump pully attached with 4 10mm bolts which must be removed in order to access the water pump bolts (12mm). Bolts are threaded right hand (clockwise to tighten, and counter-clockwise to loosen).

Posted on Oct 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford ranger fan clutch


There may be a tool, or you jam a metal tool between two metal parts.
check these out:


Removing Stubborn Clutch fan Ranger Forums The Ultimate Ford Ranger...

Fan clutch removal


Apr 11, 2017 | 1993 Ford Ranger SuperCab

1 Answer

Change the water pump


  • Tools Required
  • J 43651 Water Pump Holding Tool
  • Remove the thermostat housing.
  • Remove the water pump access plate from the front cover.
  • Remove the right hand fender liner.
    1. Important: A drain plug has been provided at the bottom of the water pump assembly for additional coolant drainage from the engine block and water pump.
    Drain the coolant from the water pump using the plug at the bottom of the pump.
    1. mportant: The water pump holding tool supports the sprocket and chain during water pump service. The tool must be used or the balance shaft must be re-timed.
    Install the J 43651 into position.
    1. Tighten the bolts on the water pump holding tool into the threads on the water pump sprocket.
    2. Install the access cover bolts that were removed earlier to secure the water pump holding tool to the front cover assembly.
    3. Remove the 3 inner water pump sprocket to water pump blots.
      1. Important: Be sure to remove both water pump bolts from the front of the engine block.
      Remove the 2 water pump bolts.
      Remove the rear 2 water pump bolts.
      1. Remove the water pump.
      2. Remove and discard the water pump O-ring seal.
      Installation Procedure
      1. Important: Prior to installing the water pump, read the entire procedure. This will help avoid balance shaft chain re-timing and ensure proper sealing.
      Install a NEW water pump O-ring seal.

      1. Important: A guide pin can be created to aid in water pump alignment. Use a M 6 m x 6 mm stud. Thread the pin into the water pump sprocket.
      Using the guide pin, align the pin with the water pump holding tool.
      1. Position the water pump against the engine block and hand tighten the water pump bolts.
      2. Notice: Refer to Fastener Notice.
      Install the inner water pump sprocket bolts. After 2 are snug, remove the guide pin and install the 3rd bolt.
      Tighten the bolts to 25 Nm (18 ft. lbs.).
      1. Tighten the water pump sprocket bolts last. Tighten the bolts to 10 Nm (89 inch lbs.).
      2. Remove the J 43651.
      3. Install the water pump access plate and bolts. Tighten the bolts to 10 Nm (89 inch lbs.).
      4. Install the right hand fender liner.
      5. Install the thermostat housing.



Aug 29, 2011 | 2006 Pontiac Solstice

1 Answer

How to locate and change water pump on 2000 buick lesabre, 6 cylinder engine


I assume you have a 3800 V6 motor in that model car. When standing with the hood open on the passenger side of the car, the water pump is located in the center of the engine. The pulley will have four small (8mm) bolts. To remove: Loosen the 4 bolts on water pump pulley.
Use 13mm socket wrench on tensioner pully to rotate and pull tension off of serpentine drive belt. Take belt off of tensioner and water pump pulleys, bend back out of the way. Finish removing water pump pulley bolts and remove pully. Remove water pump bolts (there are several of 2 different sizes, 10mm and 13mm) . Remove old pump by prying gently around the pump rim to break the gasket's seal, or tap shaft with a rubber hammer. Remove all signs of gasket material on engine mating surface with a scraper and then some fine sandpaper (1000 grit wet/dry) or steel wool. Use high-tack sealant to mate gasket to new water pump, allow to set to a few minutes. Use high-tack again on engine mating surface, allow to set a few minutes, then put water pump to engine using the small bolts tightening them finger tight. Put a small amount of black RTV sealant on larger, long bolt ends about 1/2 " of threads covered. Insert longer/larger bolts and tighten finger tight. Tighten all bolts to firm hand tight using a criss-cross pattern starting in the center top to bottom, then side to side.Do not overtighten, as damage to your new pump or striping thread holes out will result. Allow assembly to set 1/2 hour for sealants to cure. Install pump pulley. Install drive belt. Refill coolant level. Start engine, allow to warm up and check for leaks. Done! :)
Mike

Jun 11, 2011 | 2000 Buick LeSabre

1 Answer

Im trying to remove the water pump from my bmw 316i 1996 but i cant get the fan off, hav removed the allan key bolts for the outer part of the fan but cant get the centre piece off to gain access to the...


To get the viscous clutch of the water pump you first need to remove the belt pulley and remove the water pump. Then put the impeller of the water pump in a vice and using a 32 spanner screw the viscous clutch off. Note that the bolt on the viscous clutch is of left hand thread so you have to unscrew the opposite way to a normal bolt.

Sep 09, 2010 | BMW 318 Cars & Trucks

1 Answer

How to replace water pump 2003 alero. 3400 engine.


Removal & Installation 2.2L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. If equipped with an automatic transmission, remove the exhaust manifold..
  3. Drain the cooling system.
  4. Raise and safely support the vehicle.
  5. Remove or disconnect the following:
    • Right front wheel and tire assembly.
    • Right front fender liner. chevy_cav_02-04_accescover.gif

    • Access plate on the water pump sprocket from the timing cover.
  6. Install J 43651 water pump sprocket holder or equivalent to the water pump sprocket.
  7. Use the access plate bolts to attach J43651 to the engine front cover.
  8. Remove or disconnect the following:
    • Bolts that secure the sprocket to the water pump.
    • Bolt that secures the engine block to the water pump.
    • Bolt that secures the engine front cover to the water pump.
    • Feed pipe that joins the thermostat housing to the water pump. chevy_cav_02-04_wp.gif

    • 2 Bolts that secure the water pump to the engine block.
    • Water pump.
To Install:
  1. Use a threaded stud in the hub to align the water pump sprocket.
  2. Install or connect the following:
    • Water pump.
    • 2 bolts that secure the water pump to the engine block.
    • Feed pipe that joins the thermostat housing to the water pump.
    • Front cover bolt and the bolt that secures the engine block to the water pump. Tighten the bolts to 15 ft lbs (20 Nm).
    • 2 of the bolts that secure the water pump sprocket to the water pump.
  3. Remove the threaded stud.
  4. Install the last bolt.
    • Tighten the bolts to 89 in lbs (10 Nm).
  5. Remove J 43651.
  6. Install the access plate on the water pump sprocket to the timing cover.
  7. Install the access plate bolts.
    • Tighten the bolts to 18 in lbs (10 Nm).
  8. Install the front fender liner.
  9. Install the right front tire and wheel.
  10. If equipped with an automatic transmission, install the exhaust manifold.
  11. Fill the cooling system.
  12. Connect the battery ground cable.
2.4L Engine To Remove:
Water pump 2.4L 87953070.gif

  1. Disconnect the negative battery cable
  2. Drain the engine coolant.
  3. Remove the exhaust manifold.
  4. Remove the coolant intake pipe as follows:
    1. Remove the coolant inlet pipe bolts.
    2. Remove the wheel and tire assembly.
    3. Remove the engine splash shield.
    4. Remove the bolts from the transaxle-to-engine block brace and remove the brace.
    5. Remove the radiator hose from the coolant inlet pipe.
    6. Remove the coolant inlet pipe to oil pan bolt.
    7. Remove the coolant inlet pipe, thermostat and seal.
  5. Lower the vehicle.
  6. Disconnect the heater hose quick connect from the heater outlet pipe.
  7. Remove the front timing chain cover and the chain tensioner.
  8. Unfasten the water pump-to-cylinder block bolts.
  9. Remove the water pump-to-timing chain housing nuts.
  10. Remove the water pump and cover mounting bolts and nuts.
  11. Remove the water pump and cover as an assembly. Separate the two pieces after removal.
  12. Clean the mating surfaces.
To Install:
  1. Install the water pump cover to the water pump assembly.
  2. Install and hand tighten the pump cover mounting bolts.
  3. Install water pump cover assembly.
  4. Install and hand tighten the cover-to-block mounting bolts.
  5. Install and hand tighten the water pump-to-timing chain housing nuts.
    • Tighten the water pump-to-timing chain housing mounting nuts to 19 ft lb (26 Nm).
    • Tighten the water pump cover-to-water pump mounting bolts to 124 in lb (14 Nm).
    • Tighten the water pump cover-to-engine block bolts starting with the bottom bolt first to 19 ft lb (26 Nm).
  6. Install the heater hose to the water pump pipe.
  7. Using new gaskets, install the exhaust manifold.
  8. Install the oil level indicator and tube.
  9. Connect the brake vacuum tube to the cam housing.
  10. Raise and safely support the vehicle.
  11. Install the catalytic converter.
  12. Install the coolant inlet pipe.
    • Tighten the inlet pipe-to-oil pan bolt to 19 ft lb (26 Nm). Tighten the coolant inlet pipe bolt to 124 in lb (14 Nm).
  13. Install the timing chain and tensioner.
  14. Lower the vehicle.
  15. Connect the oxygen sensor.
  16. Fill cooling system and check the system for leaks.
3.4L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt.
    • Water pump pulley bolts and pulley.
    • Water pump bolts, pump and gasket.
    • Clean the water pump mating surfaces.
To Install:
  1. Install or connect the following:
    • Water pump gasket and pump.
    • Water pump bolts.
      1. Tighten the water pump bolts to 89 in lbs (10 Nm).
    • Water pump pulley and bolt until snug.
    • Drive belt.
  2. Tighten the water pump pulley bolts to 18 ft. lbs (25 Nm).
  3. Fill the cooling system.
  4. Check for leaks.
  5. Connect the battery ground cable.
prev.gif next.gif

Aug 31, 2010 | 2003 Oldsmobile Alero

1 Answer

Change water pump on 1999 Century Buick


GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Water Pump - REMOVAL & INSTALLATION

3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.

  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see .
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.

To install:

1430070.jpg

Fig. Exploded view of the water pump and front cover arrangement-3.1L and 3.4L (VIN E) engines
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

3.4L (VIN X) Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the coolant recovery reservoir.
  4. Remove the drive belt. Please see .
  5. Remove the pulley bolts and separate the pulley from the water pump.
  6. Remove the water pump bolts and remove the pump from the engine.

91d51fb.jpg

Fig. Exploded view of the water pump mounting-3.4L (VIN X) engine
To install:
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and finger-tighten the bolts.
  4. Install the drive belt, then torque the pulley bolts to 18 ft. lbs. (25 Nm).
  5. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 1998 Buick Century

1 Answer

Remove water pump have removed outer plastic blades of viscous fan and the four small bolts behind the water pump it seems loose but will not come away, is it just the internal impeller blades dont want to...


what's up led, the large viscous nut is loosened in the clockwise direction. after you remove the 4 nuts on the water pump, you should see one hole on each side of the water pump body. if you take 2 bolts out of the thermostat housing, you can use those to thread in the pump body holes.slowly tighten each bolt equally and the pump should come out. to install a new pump, lubricate the o-ring on the new pump and just push in by hand.

Mar 21, 2009 | 1996 BMW 318

2 Answers

Change water pump


If you have any questions feel free to ask. Let me know if you dont get diagrams(happens sometimes)

0900c1528004319d.jpgReverse rotation water pump—2.5L and 4.0L engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following: NOTESome 4.0L engines are equipped with a fan clutch that threads Directly on to the water pump shaft. This fan clutch is equipped with right-hand threads. NOTEDo not store the fan clutch assembly horizontally, silicone may leak into the bearing grease and cause contamination. NOTEOne of the water pump bolts is longer than the others. Note the location for reassembly.
    • Negative battery cable
    • Electric cooling fan connector
    • Accessory drive belt
    • Engine cooling fan and pulley
    • Water pump pulley
    • Power steering pump
    • Lower radiator hose from the water pump
    • Heater hose
    • Water pump and discard the gasket
To install:
  1. Clean the mating surfaces of all gasket material.
  2. Install or connect the following:
    • Water pump using a new gasket. Torque the bolts to 17 ft. lbs. (23 Nm).
    • Heater hose
    • Lower radiator hose
    • Water pump pulley. Torque the bolts to 20 ft. lbs. (27 Nm).
    • Power steering pump
    • Engine cooling fan and shroud. Torque the bolts to 31 inch lbs. (3 Nm).
    • Accessory drive belt
    • Electric cooling fan connector
    • Negative battery cable
  3. Fill and bleed the cooling system.
  4. Start the engine, check for leaks and repair if necessary.
3.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fan and clutch assembly from the pump
    • Fan shroud and fan assembly. If you’re reusing the fan clutch, keep it upright to avoid silicone fluid loss!
    • Lower hose
    • Water pump (8 bolts)
  4. Installation is the reverse of removal. Tighten the bolts, in sequence, to 40 ft. lbs. (54 Nm). 0900c1528004319e.jpgWater pump tightening sequence—3.7L

Nov 15, 2008 | 2002 Jeep Grand Cherokee

1 Answer

Water pump


WATER PUMP Removal Disconnect negative battery cable. Drain cooling system. Loosen water pump pulley bolts. Remove accessory drive belts. 1. Remove automatic tensioner. Disconnect coolant hoses from water pump. Remove retaining bolts, water pump and gasket.
Installation To install, reverse removal procedure. Lightly oil all bolt and stud threads, except bolt requiring Thread Sealant, before installing. Apply Contact Adhesive on gasket and install on water pump. 1. Tighten bolts/nuts to specification. Refill cooling system. Check for leaks when finished.

Oct 07, 2008 | 2000 Ford Taurus

3 Answers

1998 Ford Escort ZX2 Water Pump Housing removal


I am sure the leak is the water pump based on years of Escort work, The ZX2 is equipped with a 2.0L DOHC V-Tech engine. The water pump is on the front (rt side of car) of the engine block, visible with the hood up. NAPA autoparts replacement instructions are to loosen the belt drive pulley from the pump BEFORE removing the serpentine belt. Once the four bolts are loose, take the belt off (good time to replace?) remove bolts and old water pump (four more bolts)- it will be tight, but it comes out- clean gasket area and install new gasket and pump in reverse order. That includes putting the pulley on and hand tightening the bolts, put on the belt, finish tightening the bolts to the pulley.

Aug 10, 2008 | 1998 Ford Escort

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...