Question about 2002 Dodge Intrepid

1 Answer

Tranny service light came on and mechanic read

Tranny service light came on the morning after I bought this car and mechanic read these codes P0700, P0731, P1776, P0841 2 days later all but 1st gear and reverse went out. what could this mean?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

It may be a shift solenoid or a speed sensor look up the codes online google your cars year, make ,and model and be sure the fluid is not too low, check the fluid level warm while the motor is running.

Posted on Oct 05, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Code p0700 w a H02S on a chryslar sebring

year? engine? po700 usually has something to do with tranny

Jun 02, 2017 | Cars & Trucks


I get code P1775 and P0700


P1775 is the most relevant code. It means Solenoid valve latched in torque convertor.

P0700 is consequence of the P1775 code. P0700 means that there is an additional code stored in the TCM (transmission control module). The TCM stored code is probably related to the same problem. TCM codes can be pulled out at the car dealer or at an authorized garage. On this see: I get code p0700 after an OBDII scan.

P1775 is often coming with misfire codes.

P1775 means that the TCM detects that the solenoid valve located in the valve body (inside transmission pan under the filter) is not in the expected position (valve has two positions LR and TCC).
This cause rough shifting and driving problems.

Sometimes it is possible fixing the problem by resetting TCM and ECU. This is done disconneting battery cable (ensure you have anti-theft code if needed).

However, if a P1775 occurred, that means that there had been a solenoid valve malfunction, and problem must be fixed.

The first thing to do is replacing transmission fluid, and if needed also the filter. If the fluid level is poor, or if fluid is dark brown and satured with metal particles, that can cause solenoid valve malfunction.

If replacing the fluid does not help, then the most common problem causing the P1775 code is a defective solenoid in the solenoid pack.

Transmission shift solenoids are located in valve body, and they can be tested reading Ohms with a multimeter.

If that does not fix the problem (usually it does), the mechanic will proceed testing wiring to solenoid pack, TCM and solenoid valve, to find the reason of malfunction. Most common problems causing P1775 are related to tranny fluid and solenoid pack.

On automatic transmission problems see also: My car does not shift..


on Aug 17, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

No reverse. What are the probable causes of DTCs P0700 and P0780?

I own a 2003 ODY & frequent forums for answers.
General opinion is when these trannys go out, it happens quickly.
But, it never hurts to know your issues and options before taking a dealer mechanic's word.
1. Codes for Low transmission fluid: P0730 & P0780
2. P0700: Sorry, but a dealer has the HONDA diagnostic tool to find the real problem code. P0700 is a generic "transmission error" code used by after-market diagnostics.
3. Check if your "D" is lighting up on the shift indicator.

Here are some helpful links from the ODYCLUB Forum:
Note: Always check for healthy orange colored tranny fluid before re-filling. Black is BURNED and needs replace & might indicate clogged screens or worse.

Dec 16, 2015 | 2002 Honda Odyssey

1 Answer

I have grand cherokee 2001 limited the code p0700 is apper the gear is started scend shift espically in morinig

possible causes
Shorted or open circuit within Transmission Control Module (TCM)
- Faulty Transmission Control Module (TCM)
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transmission shifting problems
p0700 description
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Read more:

Oct 14, 2013 | 2001 Jeep Grand Cherokee

2 Answers

2002 chevy trailblazer LS has just had transmission replaced now service engine soon light is on cruise control stopped working ac pulls engine idle down when car stops at intersection and tranny not...

your going to ave to get under the SUV, look for the connectors going to the transmission, sounds like one of them is not pushed in all the way, or insted of pullling off the connector the correct way the yanked it by the wires, if you have an "Auto Zone" near by you can stop by there and they can read the codes for you for free, if you need to read the BCM codes you can rent the tool for free, or sometimes they will let you take it in front of the store to use it from 30sec or so. will at least point you in a direction.

Apr 04, 2017 | Cars & Trucks

1 Answer

Codes p0118, p0700,andp1781

for code p0118 the possible fixes are a bad connection to the sensor
an open on the ground circuit to the ecm
or a bad temperature sensor

for code p0700 possible tranny major issue this would have to be inspected by a tranny shop

for code p1781 not sure what that code is not familiar with this one to be completely honest

Jan 15, 2011 | Chevrolet Aveo Cars & Trucks

1 Answer

I have 2 codes that I need help with its a 05 GMC 2500HD.. PO0700 PO0735

A p0700 is a general tranny code you need to have a scan of the tranny to find out what is wrong it will be electrical but needs a complete scan most of the time trany shops have a free diagnostic, this should also show up the p0735 number which is the 5th gear incorrect ratio so its more than likely to be an electrical rather than a mechanical fault....hope this helps

Jan 14, 2011 | 2005 GMC Sierra 2500HD 4WD

1 Answer

I have a 2004 dodge neon sxt, the check engine light is on and when i drive it the exhaust is loud and the car accelerates horrible. I get it up to 30 max and it takes a little while. Got it diagnosed and...

If u have an exhaust leak (loud sound) that will affect a lot of the sensor readings. The O2 sensors will not read properly either & set codes. If the leak is large enough u will lose power & the trans wont work properly either & set codes. Just because u have a code, doesn't mean the part is bad. Start w the basics. If there is an exhaust leak, fix that 1st & clear the codes.

Mar 12, 2017 | 2004 Dodge Neon

3 Answers

Engine code p0700 need help

It is possible that there are other causes, but if you just want to replace the output speed sensor:

it should be easy enough to find. it will be along the tail shaft pointing perpendicular to the drive shaft. It will have two wires for a harness. simply unplug the sensor, put a drop pan under it in case some fluid drops out. then just wrench it out, install the new one and hook everything back up. check fluid level if applicable... good luck

May 14, 2009 | 2000 Dodge Durango

1 Answer

Check engine code p0700

this code is a transmission code and has a few different tranny sensors that is reads. you could just be low on tranny fluid or is could be the tranny axle speed sensor. odds are if its running fine now it is just low fluid but you could look into the sensor after that. the sensor is what tells the truck when to shift so thats could be why it went up in rpms if the sensor went out bacause then it would know exactly how to shift.

Mar 31, 2009 | 2001 Dodge Dakota

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

781 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides