Question about 1993 Mitsubishi Eclipse

1 Answer

What is the name of the oil thing that oils the crankshaft that is located close to the timing belt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 373 Answers

I recommend you get yourself a Haynes Manual #68030. and look for a picture of the oil thingy. you have me stumped.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long and easy is it to rebuild oil pump on 94 grand caravan 3.8l


Don't bother. Replace the unit.
3.0 liter
The oil pump assembly used on this engine is mounted at the front of the crankshaft. The oil pump also retains the crankshaft front oil seal.
  1. Remove the accessory drive belts.
  2. Remove the timing belt cover and timing belt. Refer to the timing belt removal and installation procedures in this section.
  3. Remove the crankshaft sprocket.
  4. Remove the oil pump mounting bolts (5), and remove oil pump assembly. Mark mounting bolts for proper installation during reassembly.

To install:
  1. Clean the oil pump and engine block gasket surfaces thoroughly.
  2. Position a new gasket on pump assembly and install on cylinder block. Make sure correct length bolts are in proper locations and tighten all bolts to 10 ft. lbs. (14 Nm).
  3. Install the crankshaft sprocket and timing belt. Recheck engine timing marks.
  4. Install the timing belt covers. For more details, refer to the timing belt cover installation procedures.
  5. Install the accessory drive belts.
  6. Refill the crankcase and start the engine.
  7. Check for correct engine oil pressure and for any oil leakage.
3.3 and 3.8 liter engines


  1. Disconnect the negative battery cable. Remove the dipstick.
  2. Raise the vehicle and support safely. Drain the oil and remove the oil pan.
  3. Remove the oil pickup.
  4. Remove the chain case cover.
  5. Disassemble the oil pump as required.

To install:
  1. Assemble the pump. Tighten the cover screws to 10 ft. lbs. (14 Nm).
  2. Prime the oil pump by filling the rotor cavity with fresh oil and turning the rotors until oil comes out the pressure port. Repeat a few times until no air bubbles are present.
  3. Install the chain case cover.
  4. Clean out the oil pickup or replace as required. Replace the oil pickup O-ring and install the pickup to the pump.
  5. Install the oil pan.
  6. Install the dipstick. Fill the engine with the proper amount of oil.
  7. Connect the negative battery cable and check the oil pressure. Check for any oil leaks.
for the 3.3 you can rebuild, 3.0 - replace.

Feb 15, 2011 | 1994 Dodge Caravan

2 Answers

I AM LOOKING WHERE IS THE OIL PUMP IN 2003 KIA SEDONA ENGINE


take the sump off and you will find it ,to get the sump off you will need to remove the engine

Jun 27, 2010 | 2003 Kia Sedona

1 Answer

Where is the oil pump located on a 2003 isuzu rodeo sport 4 cyl.?


Timing Cover Assembly



Oil Pump
Removal
  1. Disconnect battery ground cable.
  2. Drain engine oil.
  3. Remove crankcase assembly.
  4. Remove crankshaft pulley.
  5. Remove timing belt.
  6. Remove timing pulley from crankshaft.
  7. Remove four fixing bolts from oil filter assembly.
  8. Remove oil strainer fixing bolts, remove oil strainer assembly with O-ring.
  9. Remove three bolts from oil pipe and O-ring.
  10. Remove eight oil pump fixing bolts, then oil pump assembly.
  11. Remove sealant from mounting surface of oil pump assembly, cylinder block and take care not to damage mounting surfaces of oil pump and cylinder block.

Jun 04, 2010 | 2003 Isuzu Rodeo

1 Answer

Where is the oil pump located


On a 3.3L and 3.8L engine oil pump sit in back of crankshaft gear.

On a 3.0L engine oil pump sit in back of timing belt.

Both sit in front of crankshaft gear in front of engine.

May 28, 2010 | 1999 Plymouth Voyager

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

3 Answers

Oil pump is leaking on 1996 toyota camry, 2.2 lt


Since your friend just replaced the timing belt, there wouldn't be a need to replace the oil pump O-ring and crankshaft seal unless they were leaking.

No, you cannot get to the oil pump unless the crankshaft, lower timing belt cover and belt are removed.

I have the same exact car with the same engine and just replaced the oil pump O-ring and crankshaft seal. I'm a good mechanic, but this is a tedious and time consuming job, but It can be done if you have good mechanic skills.


VERY IMPORTANT.
There is a big chance that the car's engine timing will be off, have someone who is knowledgeable to set the engine timing. If you don't and try to start the car, serious engine damage will probably occur.

ALSO IMPORTANT.
When you get the oil pump off removed all the old O-ring the new oil ring will not stay in place, I used petroleum jelly to keep the ring in place, it's perfectly safe and won't affect the operation of the oil pump.

If your not sure you can do the repair yourself, take it to a mechanic.

Mar 08, 2009 | 1996 Toyota Camry

1 Answer

1999 cross country v70 awd crankshaft seal replacement


Your info is confusing. The rear cam seal is not inside the timing belt cover, and the crank seal is at the bottom of the engine, while the cam seal is at the top.

Is there oil at the top, around the cam seal? Or just at the bottom? It's common for the oil pump seal to leak. If you get the oil pump reseal kit, it contains the oil pump seal and gasket, as well as the crankshaft seal. Make sure you seal the oil pump bolts, Volvo has special copper washers for this purpose.

Just try to locate the oil leak before replacing any more parts. Sometimes it can be something simple like the oil cap seal or the oil trap housing.


Bret
RepairPal.com

Nov 23, 2008 | 1999 Volvo V70

1 Answer

Mazda Premacy Timing Belt Change


Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.


The Front Oil Seal must be replaced when the Timing Belt/Chain is replaced. It is located behind the Crankshaft Pulley on the Crankshaft.

Nov 14, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
1993 Mitsubishi Eclipse Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...