Question about 2000 Ford Crown Victoria

3 Answers

2000 Crown Vic cranks but won't start.

I own a 2000 Ford Crown Victoria Police Interceptor. It had been running fine, but now it won't start. It cranks fine. I checked the Fuel Filter and it seems fine. I tried starting it without the fuel filter attached and no gas came out of the line, so I figured it was the fuel pump. I tried starting it a few days later after reading about the fuel pump reset switch, and it started for a second, but wouldn't stay running, and it is now back to not starting at all. Could this be the fuel pump relay, or do I need to change out the fuel pump?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Check the fuel pump reset switch again, if it is popped back out then replace that little switch in the trunk, any ford one will do. it works off a magnet and a bearing to close the circuit for the fuel pump. easy fix.

Posted on Dec 20, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check your MAF (Mass Air Flow) Sensor. My brothers had insects in it, cleaned them out, cleaned it up, everything's fine now.

Posted on Jul 21, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,869 Answers

Your fuel pump is semi-shorted causing high amperage
replace it

Posted on Oct 05, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 66 Answers

SOURCE: 99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Posted on Jul 07, 2009

  • 58 Answers

SOURCE: 2006 crown victoria - no heat

I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Posted on Jun 21, 2008

dsakrison1
  • 65 Answers

SOURCE: 2000 crown vic police interceptor bypass a/c clutch pulley

you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Posted on Oct 06, 2009

  • 2 Answers

SOURCE: Headlights turn off while driving

Headlight module under the dash. It is the size of a box of crackers, not a small part.

Posted on Feb 24, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need fuse panel diagrams for ford crown victoria

For check passenger compartment fuse panel, is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses.

Other details and descriptrions can find it in 2003 Ford Crown Victoria - Owners Manual (page 164 and next).

Hope helps (remember rated this).

Posted on Aug 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2007 Crown Victoria Police Interceptor vibrate when I get to 40 miles an hour and then die off back to normal by the time it reaches 50


Ford Crown Victoria Questions - what would cause a whole ...

www.cargurus.com > Questions > Ford > Crown Victoria
CarGuruswhat would cause a whole car vibration when going between 48 and 65 mph, even ... Asked by Dfranz Aug 29, 2013 at 11:53 AM about the 2001 Ford Crown Victoria Police Interceptor ... You have an open diff by turning one wheel the driveshaft should turn before the .... 2007 Ford Crown Victoria Police Interceptor For Sale.

Nov 03, 2015 | Cars & Trucks

1 Answer

2006 crown Vic police interceptor former police


The police package interceptors had a common problem with the fans seizing up. There was a TSB ford released to correct the issue which called for the replacement of the electric fan assembly with an updated fan assembly.

Sep 30, 2014 | 2006 Ford Crown Victoria

1 Answer

My 96 crown vic police interceptor, cranks won't start without spraying starter fluid.. the car won't start without spraying starter fluid into air intake hose to carb...


starting fluid is a thing of the past. dont use it. this car doesnt have a carb, its a throttle body/ electronic fuel injection system. you most likely have a fuel pump or fuel pressure regulator issue. test the fuel pressure, should be anywheres from 35-50 psi

Oct 11, 2011 | 1996 Ford Crown Victoria

1 Answer

Looking for rearend for ford crown victoria police interceptor


I have one. LBrown1806@juno.com. Selling my 1999 crown vic PI on Unocardealers.com zip code 55057. Please check it out.

Jul 16, 2010 | 1999 Ford Crown Victoria

1 Answer

2000 crown vic police interceptor bypass a/c clutch pulley


you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Oct 05, 2009 | 2000 Ford Crown Victoria

1 Answer

99 crown vic police interceptor steering wheel??


i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Jul 07, 2009 | 1999 Ford Crown Victoria

1 Answer

2005 Crown Vic Police Interceptor: Starts then stalls


Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Nov 27, 2008 | 2005 Ford Crown Victoria

2 Answers

Ford Crown Vic p0300 random cylinder misfire


take a look at the EGR valve it could be either vacum controlled or electronic either way what seems to be the problem is that the valve is stuck in the open position until the engine warms up you can gently tap the egr valve with a small hammer or a screw driver and you can see that it runs smooth, now if the egr valve is vacum controlled replace the valve. if it is electronoc controlled replace the valve and the module for the egr valve.

Nov 02, 2008 | 2000 Ford Crown Victoria

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

2,906 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...