Question about 1994 Chrysler Concorde

2 Answers

Need to figure out how to disconnect the factory alarm on a 1994 chrysler concord . Took out the fuses and still is going off.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

With the doors locked by the power lock switch use the ignition key in the pasenger door. watch the light on the dash for the alarm turn the key forward and back until the light stops blinking

Posted on Oct 09, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 17,970 Answers

Maybe in here you can find information about Wiring Alarms:
- Commando Car Alarms (for 1994 Concode)
- 1994 Chrysler Concorde Alarm Information

I hope helpy you with this. Good luck (remember rated this help).

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 1994 chrysler concorde.ran fine untill my wife set off the manufacter`s alarm system,now it will turn over but wont start even when i shut the alarm off. now like i said it turns over


Try disconnecting the negative battery connection and leave it disconnected for about 15 minutes. Then reconnect it, make sure the alarm system is still turned off and it should fire. Sometimes an alarm condition can scramble the MP and removing power for a time will clear the fault. Good luck.

Nov 03, 2011 | 1994 Chrysler Concorde

1 Answer

I have a 2008 chrysler 300 and I installed an alarm system. I connected the factory horn to the alarm using a relay. I installed a relay under the hood and got the power from the battery the problem is...


you have either a blown fuse or the factory wire harness isnt connected to horn first check fuse owners manual will have location and description of fuses if ok retrace your steps when you hooked horn to new alarm you disconnected wire at horn or you cut the wire to access horn wiring

hope this helps
plz vote leave a comment if need more help reply

Jan 18, 2011 | 2008 Chrysler 300

1 Answer

Need a diagram of the fuse pattern for a 1994 Chrysler Concord


you might find the fuse diagram on the inside of the cover of the fuse box under the hood ......hope this helps.....cheers

Aug 04, 2010 | 1994 Chrysler Concorde

1 Answer

How to disable an alarm for a 1994 Chrysler Concorde


Hello,
This is how you go about it:
Normally, you would insert the key in
the drivers door, turn left, then right
to disarm and reset it. If yours is malfunctioning,
you can disable it for good by doing the following:

The FACTORY ALARM DISARM is the
lt.green/orange 20 gauge
|-| negative wire in either kick panel,
at the door harness.
That's the area behind the plastic coverings
at your left leg area, or at the same spot
on the passenger side.

Once Located, splice into this wire with
a simular guage wire, and put it to
a solid chassis ground. This terminates
the alarm functions entirely.

However, at this point, this car would be exceedingly
easy to steel. It's up to you to protect it from here
on in.

Good Luck with it.

Aug 04, 2010 | 1994 Chrysler LHS

1 Answer

Factory alarm will not go off i do not have the p ush button remote for it the car is a 95 concord


with the alarm going lock the doors and then unlock the door with the key it should stop

Sep 20, 2009 | 1995 Chrysler Concorde

1 Answer

Lighter won't work/Wiper fluid sensor-94 Chrysler Concorde


u can check the fuse if the fuse is good replace the lighter assembly first check fuse and connection make sure u have 24v there

Jun 20, 2009 | 1994 Chrysler Concorde

1 Answer

1994 Chrysler Concorde - In Limp Mode


I had the same problem with my 94 Concord. After reading the Factory repair manual I took the car to a close friends transmission shop. He up dated some of the parts with Heavy duty parts. Its been fine with 35,000 more miles on it.

Nov 20, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
1994 Chrysler Concorde Logo

500 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...