Question about 2004 Honda Odyssey

1 Answer

AC blower only works on #5 fan speed. Compressor will not engage

Our AC blower only works on level #5 fan speed. The compressor will not engage either with the AC "ON". Fuses are good. Refrigerant level is good. Checked with AC system gauges.

At the dealer now!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

Evaporator board needs replacing located inside blower area under dash

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Toyota Corolla AC Blower/Fan will not turn on, I replaced the Blower/Fan a few weeks ago,


A/c compressor works fine and the blower motor works and shutdown right? it is the problem with the blower resistor or with blower motor relay. try to direct the resistor irrespective of the speed. hope the problem may be solved.

Jun 05, 2014 | 2003 Toyota Corolla

3 Answers

The a/c on my 2010 Mercury Milan quits blowing after about 2 hours of driving. Any ideas?


Sounds to me like the A/C clutch is no good and out of adjustment.You should goto your nerrest junkyard and get a used assembly take the clutch off then you learn how it comes off and install it on yours the save the pump for later use if needed. The clutch should only have a .010 air gap after install between th inner elctro magnet and the clutch plate it's self.

Aug 04, 2012 | 2010 Mercury Milan

1 Answer

Compressor and fans do not turn on until rev engine


I passed this question the first time I read it, so I will take a stab at it now.
The fans don't come on until the compressor has pumped the freon pressure up to say 150 or 200 psi. And the compressor clutch has to have voltage to engage the clutch.
I wonder if the clutch is going and needs 14 volts instead of 12 to engage ? Or the relay that powers the clutch ?
Speeding up the engine would increase voltage from the alternator.
This is assuming the serpentine belt is tight and everything else is working correctly.
I think I would swap the relay with another and put a meter on that circuit to the ac clutch to see what it takes to engage it.

Jul 24, 2012 | 1992 Buick Regal

1 Answer

Ac compressor clutch will not engage on my 98 yukon.


The most common cause of no clutch engagement is a low state of refrigerant charge in the system. Have a set of AC pressure gauges hooked up and bypass the compressor cycling switch and check the pressure on the low side charging port, you show shop 28-32 PSI at idle.

Jun 24, 2012 | Cars & Trucks

1 Answer

My 1991 isuzu trooper heater blower fan is not working, nor when i turn it to the airconditioner the compressor does not engage. i checked all the fuses except the ac relay fuse block, what could the...


if the lower fan speeds dont work but the fastest speed does the heater fan resistor block needs replacing. If the highest fan speed doesnt work leave it on there and check for power at heater blower fan, if power is on one wire and the other is an earth the blower motor fan needs replacing. Use a normal globe test light to check this. If no power on any wires to fan go back and check all fuses in car and under bonnet with same test light. If fuses are ok possible open circuit wire to fan.

Jan 13, 2011 | 2004 Isuzu Rodeo

2 Answers

AC does not work. Compressor will not engage Blower only blows on high speed. Is the two a related problem? Where should I look to solve the problem


The most common reason for the compressor not engaging is low refrigerant pressure. The ac system has a safety switch that will not allow the compressor to engage when there is not enough refrigerant pressure because the the refrigerant carries the compressor lubricant throughout the system. Have the system checked for proper charge. You probably have a leak. The fan is probably a separate issue.

Jun 19, 2010 | 2002 Ford Taurus

1 Answer

Air conditioner compressor runs - freon is up to proper level....not cooling??


BOTH High and low readings should be checked to have a better idea of what is going on with an AC system but based on the limited information… the compressor is not engaged or is not pumping. Below are some things I would check;

1. Check the high and low gauge readings with the AC on & set on MAX/Recirculate, middle vents with the engine at 2,000 RPM’s, blower speed on high.

2. Check the vent temperatures with a thermometer from the middle vents, far right & far left vents?

3. What is the outside temperature at the time the readings were taken?
4. Check to see if the condenser fan blowing strong?

5. Notice if compressor clutch is cylcling excessively.
Could be overcharged, not enough air going across condenser fins, compressor not pumping sufficiently… BOTH gauge readings are really needed to get a better idea.
Below are normal car AC pressure readings with 134A.

Normal readings on high and low side with AC OFF (static pressure) – Depends on outside temperature, but normally is between 80-105 PSI

Normal low side reading with AC on high speed and MAX & engine at 800-1000 RPM’s – Ranges from 25-35 PSI

Normal high side reading ranges from 200-350 PSI

Don’t assume that if adding little Freon is good that adding a lot is better! Overcharging just a little can decrease the performance of the system and possibly damage the compressor

Thank you for using fixya and good luck, keep me posted. Be glad to help you get your A/C running again soon.

Jun 12, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Ac use to work fine up until now. I don't know if its a fuse or what. Where is the ac fuse located at, in a 97 crown vick


When you say the ac is not working, do you mean the blower or the compressor is not engaging. If the compressor is not engaging, the system is low on refrigerant and needs to be checked for leaks and recharged. If the blower is not working, it will most likely be the resistors in the multiple speed switch.

May 26, 2010 | 1997 Ford Crown Victoria

1 Answer

The fan in my truck only turns on on high speed.


A bad blower motor resistor will cause it. It is located ny the blower motor p.s. below dash.

Sep 28, 2009 | 2000 Chevrolet Silverado

1 Answer

AC compressor works fine, Blower does not. How do you repair?


check the fuse in the fan-fan relay-check voltage at the terminals of the blower if you have the voltage problem is to check the blower motor of the blower speed control

Aug 11, 2009 | 2006 GMC Sierra

Not finding what you are looking for?
2004 Honda Odyssey Logo

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...