Question about 1983 Ford Bronco

1 Answer

Need to know origin and destination of all vacc lines. the boy diconnected them without marking them.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

The place to find a diagram of the engine vacuum routing is the library.You will also need the engine calibration on the left valve cover(if it is there) size of the motor,and if it's a manual or automatic.These had a lot of vacuum hoses and were a nightmare

Posted on Oct 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set time with light


Most timing lights have to cables with clamps that connect to the vehicle battery. A third wire is clamped over or put in line with the number 1 spark plug wire. Some vehicles require the vacuum advance be diconnected and the vacuum hose plugged before timing. The engine pulley bolted on the crankshaft usually has a mark that will be illuminated by the timing light when the engine is running. This mark has to be lined up with the proper mark on the engine block . Turning the distributor moves the mark back or forward. Adjust till timing marks line up.
Hope this helps.
Bob

Jul 12, 2015 | Cars & Trucks

1 Answer

On my 1999blazer my A/C does not cool, it's full of freon and it builds pressure to the point it blows off on the back side of the engine and when I turn the a/c or heat on it really pulls the eng


boes the blend door work when you move selector to face setting does it change to face? if not this system works off vaccume lines under hood if you look on top of engine you will find that one of these vacc lines is broken ...find repair relax..stay cool ...you can use short peice of vacc line from parts store..

Aug 16, 2012 | 1999 Chevrolet Blazer

1 Answer

99 chevy vorte marks wont line up


if you lined up marks on cam and crank gears when you installed timing chain and you used the original timing cover and timing mark tab and did not turn engine before checking the marks the balancer is spun and needs to be replkaced if the engine has been turned it may be 180 degrees out of time you will need to turn engine at least two full revolutions and recheck maybe upto 4 times if it still does not line up with all original parts no chrome timing covers or timing tabs the balancer is bad and needs replaced

Mar 27, 2012 | Chevrolet Tahoe Cars & Trucks

1 Answer

Changed all for calibers and bled from passanger rear to driver front tire. I get good pedle after three pumps. Start the truck and pedle goes to floor and will not pump up


it could be the slave silander or it could be the vacc line going to the booster . I have buyed a new slave silander an it was bad .I would check the vacc check valve it is on the hose that come out of the booster for the vacc check valve .

May 01, 2011 | 2000 Chevrolet Silverado

2 Answers

Need to know the timing marks on 1992 toyota


you may find them online but if it were me i would go to local auto parts and spend the $24.95 on a haynes repair manual it has pictures of the marks and the tension specs etc worth the $$ , remove #12 spark plug and take a peice of wire stick it into the hole till it touchs the piston then rotate the crankshaft till its a top dead center then look down at the line up marks behind the crank gear they should line up then rotate the camshaft till marks line up should be 12 oclock on cam gear? this is sometimes tricky to get it lined up without it being 1 tooth off thats why picture is best ? hope this helps autodoc01@live.com

Aug 27, 2009 | 1992 Toyota Corolla

2 Answers

2004 Ford F150 Airconditioning wont blow through panal vents only through defrost but vent works


check vacc line from engine into fire wall. behind batt is where they normally crack and leak. possible from a leaking batt at one time. check black supply vacc line right behind battery

Jul 10, 2009 | 2004 Ford F150

1 Answer

DOES ANYONE HAVE ACCESS TO A FACTORY VACC. DIAGRAM


This is for the V6, sorry the quality is poor, if you need one for the 4 cyl. let me know I have that also. If this shows up really badly, I can email it to you hi-res.b8f449f.jpg

May 16, 2009 | 1985 Ford Bronco II

1 Answer

The heating unit blows air from defroster and floor only


defrost is a default if vaccum is lost from engine.. check behind batt in engine comp to see if batt has been leaking. this can cause the acid to drip on small black vacc lines from engine and cause a leak in the vacc system causing it to only blow in defrost . you can fix by cutting damagged vaccumm line and install a small rubber hose over cut ends .. the vaccum lines run between batt and fire wall

Mar 10, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Time belt


Before removing belt when you rotate crankshaft the MARK will all line up as shown in the picture. Then you loosen tensioner and remove belt there is no need to rotate the pulley to remove and install belt. However if you removed belt without first lining up marks then you need to Line up Crankshaft first by turning cylinder #1 on TDC=top dead center the piston has to be all the way up on COMPRESSION STROKE then line up cam marks. Good luck its pretty simple.

Jan 25, 2009 | 2000 Daewoo Leganza

Not finding what you are looking for?
Cars & Trucks Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...