Question about 2002 Land Rover Range Rover

Open Question

Range rover rear wiper motor

How do I remove interior trim on rear tailgate of L322 Range ROver so I can replace wiper motor

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Range Rover 1990 abs pump

Ok, your light WILL go out, and go back to normal once repaired, so don't fret.

Unless the pump was really loud (bad internals), you likely burned up the pressure switch (green thing on end of pump), which can be purchased in LA, USA; or through me, GreenDog Oregon (store name on Ebay US). These go out due to the pump running for an extended peroid of time, overheating the entire assembly, and allowing moisture into the pressure switch (Yes, they do go bad, and I have pictures of the inside of a bad one, full of brown muck). The reason this happens is bacause the nitrogen charge in the ABS accumulator (ball like canister attached to pump) has a limited life-span, and goes bad after about 7 years (Rave 2003). This means that the pump must run more often to accomidate braking, as it has no assist.

So, you can replace the Accumulator, and the pressure switch, and will likely be back in commission, after a proper bleeding, of course (directions for proper bleeding in Rave 2003 -CD available on ebay for appx $5)

Or, you could just replace the entire assy with a nkown good used part, and since the switch on the used part will likely be good, you can then just replace the ABS accumulator. The pressure switch is very hard to find, but I do have a couple of sources, here on the West Coast.

If you need further assistance or need a pressure switch (or parts), contact me through my ebay store, GreenDog Oregon. If you have trouble finding my store, just look for P38 and Classic parts, I'll be near the top of the store listings, as my prices are low, due to the low cost of rovers in the NW.

Posted on Oct 04, 2008

  • 45 Answers

SOURCE: Programming a used 2005 Range Rover key FOB

Unfortunately I believe that will require a trip to the dealer, and a hefty price tag to go with it. Most dealers refuse to let anyone else handle their security systems. And most keys have the alarm keypad built in making it even more dealer specific. I wish I could give better news.
Dynami

Posted on Mar 27, 2009

  • 1757 Answers

SOURCE: how do i change drive belt on p38 range rover

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

Not sure if this what you need for the "P38" but it is for the 1996 Range Rover.

I do not know if you still need this information, but I am going ahead and answering it anyway.


Click on the following Link. It has the several Serpentine Belt Diagrams, one of which matches your specific vehicle with your particular options (AC, Power Steering etc..).

Regarding HOW:
Standard Rule to Removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Rotate/Move the Tensioner away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys
.
Standard Rules for Installing the Serpentine Belt:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.

b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1996/make/land_rover/model/range_rover/1996_land_rover_range_rover_drive_belt_routing_diagram.htm

Posted on Mar 13, 2010

  • 23 Answers

SOURCE: range rover l322 2002 heavy power steering renewed

there is a pressure sensor on the steering rack which can cause this fault did rack come complete or did you have to swap anything over

Posted on May 23, 2010

  • 3072 Answers

SOURCE: my 2005 Range Rover radio

Sounds like your anti-theft is locked, if you do not know the code you can check with the dealer all he needs is the vin

Posted on Aug 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Range Rover L322 steering lock ECU Part number and replacement


I have the same issue, has anyone yet managed to find a solution that doesn't involve changing the whole steering column?

Sep 21, 2012 | 2005 Land Rover Range Rover

2 Answers

Range rover l322 2002 heavy power steering renewed


The Solenoid fitted on the Steering Rack is not getting the command from The Body Control Unit. Kindly Replace your BCM and then your problem is solved. You can try to make sure by giving direct current of 12v to the solenoid and check the Steering. if it works then simply change the BCM as it's not giving d command to the Solenoid. Salman EiD

May 15, 2010 | 2005 Land Rover Range Rover

2 Answers

How do you remove rear wiper on 1997 range rover 4.6 HSE


if you have an autozone or any parts store near you and you get the blade from them they will help you install it give these websites a try www.alldatadiy.com and www.autozone.com wish you the best Michigan Man

Nov 04, 2009 | 1997 Land Rover Range Rover

1 Answer

Range rover l322 power steering not working


check the power steering oil and try to check the cable too


rate this

Oct 29, 2009 | 2005 Land Rover Range Rover

1 Answer

Range Rover Sport Pinion and introduction


This new five-passenger premium sport-utility vehicle filled a price gap between Land Rover's LR3 and its ultraluxury Range Rover models. In fact, the all-wheel-drive Range Rover Sport was smaller than either, designed to compete with "high-performance" SUVs such as V8 versions of the BMW X5 and Porsche Cayenne, as well as Cadillac's SRX. Based on the seven-passenger LR3's body-on-frame structure, the Range Rover Sport came as the HSE model with a 300-horsepower, 4.4-liter V8, and in Supercharged trim with a 390-horsepower, 4.2-liter V8. Both engines were sourced from Jaguar, which was owned by Land Rover's parent company, Ford. A six-speed automatic with manual shift gate was the sole transmission. All-wheel drive with low-range gearing was standard, and included Land Rover's Terrain Response system, designed to automatically tailor AWD performance to specific off-road conditions. Also included were a height-adjustable air suspension, antiskid/traction control, and antilock four-wheel disc brakes. The Supercharged model came with 20-inch wheels and Brembo-brand front brakes. On the HSE, 19-inch tires were standard and 20-inch optional. Both models contained front side airbags, head-protecting curtain side airbags, and a navigation system. Standard on the Supercharged model and available for the HSE were wood interior trim, heated seats, and Land Rover's Dynamic Response suspension system, designed to counteract body lean in turns. Satellite radio, wireless cell phone link capability, and rear DVD entertainment were options. Adaptive cruise control was available for the Supercharged edition.

May 14, 2008 | 2006 Land Rover Range Rover Sport

Not finding what you are looking for?
2002 Land Rover Range Rover Logo

Related Topics:

683 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7712 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...