Question about 1999 Volkswagen Passat

Open Question

My abs brakeslight is on and the motor is making a

My abs brakeslight is on and the motor is constantly running and making a noise . I want to know what is the problem and how to fix it ?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Traction control problem


Grinding noises when making turns in front wheel drive cars usually is constant velocity joints.

Mar 04, 2016 | Cars & Trucks

2 Answers

Abs motor runs constantly


take to brake specialist,there is no abs motor

Jul 09, 2015 | Cars & Trucks

1 Answer

I have a 2005 Tahoe and recently the SERVICE STABILITY came on the dash board. It makes a real high pitched squealing noise while driving and it's now constantly making the noise. And getting worse. I know...


This stuff is my specialty, sounds like POSSIBLY your abs pump motor failing (the abs module mounts to the abs hydraulic pump where all the brake lines go into) i.e abs module=brain abs pump=muscle to put it simply. get the fault code(s), its going to be something like C0265 or C1214 basically "C" then 4 numbers. I can tell you EXACTLY what your problem is WITHOUT having to throw a bunch of money away by replacing unnecessary parts.
found this:
  • BRAKES - SQUEAK NOISE ON BRAKE PEDAL APPLICATION
TECHNICAL SERVICE BULLETIN
Bulletin No.: 08-05-22-002C
Date: April 07, 2009
Subject:
Squeak Noise On Brake Apply (Remove Brake Fluid from Master Cylinder and Refill)
Condition
Some customers may comment on a squeak noise when the brake pedal is applied or when released. This noise is normally heard when the brake pedal is slowly applied with the engine on or off, but can occur when the brake pedal is released. The noise may be isolated to the master cylinder area.
Correction
To correct this concern, remove as much of the old brake fluid from the master cylinder as possible and refill with a new DOT 3 brake fluid, P/N 88862806 (in Canada, use P/N 88862807). Start the vehicle and fully cycle the brake pedal until the noise diminishes to allow the new fluid to enter the system. hope this helps! -Tim

Jun 06, 2014 | Cars & Trucks

3 Answers

My volvo v70 2002 is showing the warning 'abs/anti-skid service reqd', also the driver side front wheel makes a screeving sound not unlike worn doiwn pads on discs when making a right or left


Felix any noise coming from the front wheel while turning leaves me thinking front constant velocity joint if the car is front wheel drive. With the abs light on I would take down the front driver side wheel and check the brakes for wear along with the front wheel bearing assembly for play or loosness, Check for the sensors to make sure they havent came off and are rubbing your rotors as you make your turn. It can be a number of things. Usually when its the front constant velocity joint it makes a popping noise as if something is binding. As for the front wheel bearing assembly it could make noises usually after the car has been ran down the road and heated up the bearing then it will sing to you. But as you mentioned about the noise only during turning I would lean towards constant velocity joint or sensor hanging and rubbing the rotor, Its only one way to find out. Hope this helps.

Jan 03, 2012 | 2002 Volvo V70

1 Answer

2003 tahoe abs light just went on around the corner from my house, so i parked the truck and its making a noise but the truck is off


if truck is off and you hear a motor running it is probabl;y the abs unit running. the ebcm module is bad and causing motor to run all time. slide under truck under drivers seat area and you will see abs motor unplug it for now this will stop from running will need to replace ebcm to correct

Aug 23, 2011 | 2003 Chevrolet Tahoe

2 Answers

Abs light is on my pick up truck but when i turn off the truck a running motor sounds under the truck. what does it means? and would it damaged my truck if i keep driving it?


OK, the ABS light being on is caused by a sensor that is pretty cheap, especailly since its just as easy to replace. The rear end/third member has a sensor on top in the middle. Remove the wire harness from the sensor, socket and 7/16 or 10mm should be right size. Unscrew, remove, replace with a new one, put screws back in, connect the plug. Light should go out. Keep in mind I dont know the year of your truck, but thats the ABS light issue. As to the noise your hearing, definately locate the exact source of where it is and go from their. It would be a good idea for anyone who has a car/truck, to have a Haynes or Chilton manual for the year make and model of that vehicle. Lots of good stuff in those books about everything. Good luck

Feb 21, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Abs motor running


either a bad abs unit or the relay/circuit

Sep 11, 2009 | 1999 GMC Suburban

3 Answers

Where is the abs control module located on a 02 chevy avalanche ?


THE EBCM IS BAD this is the electronic control module that is on abs pump. you can replace seperate I think it is around 500 for part

Dec 30, 2008 | 2002 Chevrolet Avalanche

Not finding what you are looking for?
1999 Volkswagen Passat Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...