Question about 1997 Lincoln Town Car
This cannot be safely explained on FixYa.
Go to the "Reference section" in your public library and locate the Chilton's or Motor's manual for your vehicle.
They contain step-by-step instructions, illustrations / pictures, special toolss information, torque specs, etc.
Photocopy the pages that you need using the public copy machines (15 ~ 25 cents per page).
Posted on Oct 05, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: lower ball joint removal how to
Posted on Sep 12, 2008
SOURCE: upper and lower ball joints
Your better off have it done bt a tech because you need a press to press them out and in. Also you will have a warranty witk the work. You want to be safe messing with your steering and suspension. I hope this helps.
Posted on Dec 05, 2008
its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them
Posted on Mar 31, 2009
SOURCE: Lower Ball Joint
You will have to remove it and replace it with a new one. The general steps for doing that is: 1)remove the tire 2)remove the caliper and rotor 3)remove the outer tie rod from the spindle 4)remove the axle nut 5) remove the cv axle 5)remove the nut on the ball joint 6) bang ball joint out and press in a new one. Then reassembly is exactly the reverse as disassembly.
Posted on Jun 10, 2009
Tips for a great answer:
Dec 06, 2015 | Dodge Cars & Trucks
Oct 15, 2014 | 2002 Buick LeSabre
Oct 05, 2012 | Cars & Trucks
Jan 31, 2012 | 1991 Mercedes-Benz 420
Jan 22, 2012 | 2001 Ford Expedition
To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.
NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.
CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.
CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.
CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.
Mar 07, 2011 | 2000 Dodge Caravan
Dec 05, 2010 | 1997 Dodge Stratus
Nov 28, 2010 | 1994 Pontiac Grand Prix
Jan 07, 2009 | 2001 Mazda B-Series
Sep 24, 2008 | 1999 Ford Taurus
102 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: