Question about 2003 Ford Focus

1 Answer

Hi , I am hoping you can me i need the Stell Heat Hose line that goes right under the dampner pulley i am not sure where it goes to or comes from but i do know that it is steel and it is on the right side of the car i have called many ford garage but THEY have no idea what im talking about PLEASE Help

Posted by on

  • imcookie33pa Oct 05, 2009

    yes but i cant find it any where someone said they dont make it anymore but i do know its the only steel hose in the car where can i find it please

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

Let me confirm - Do you want Steel heat hose. Check below certain links that might match what you are looking for :-

http://cgi.ebay.com/ebaymotors/DEI-010404-HEAT-SHEATH-HOSE-LINE-SLEEVES-1-1-4-x-3_W0QQcmdZViewItemQQ_trksidZp3286Q2ec0Q2em14QQhashZitem3351e44ed9QQitemZ220417248985QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

http://www.paragonperformance.com/

http://shop.ebay.com/i.html?_kw=Steel&_kw=hose&_kw=line&_ckw=Heat&_trksid=p3286.m104.l1198

Let me know, if need further assistance.

Thanks!!

Posted on Oct 05, 2009

  • taran_2005
    taran_2005 Oct 05, 2009

    Thanks for your response!!

    I offered you 3 links. Check those, if you could find the hose out of the 3 links mentioned in the solution i offered initially.


    Any further assistance, let me know.


    Thanks.


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1999 Chrysler Cirrus. The serpentine belt came off that goes to the alternator and the air conditioner unit, I was told by a mechanic that the dampner pulley is bad. Some autopart sites have a...


Hi, assuming you have the 2.5 liter engine, your damper is integral to the pulley assembly as shown in the second figure below, so there is only one part involved. You can see an example of the part here: http://www.autozone.com/autozone/parts/Dorman-Harmonic-Balancer/1999-Chrysler-Cirrus/_/N-jddk1Z93y2h?counter=0&itemIdentifier=917091_0_0_
If you look carefully at the pic below, you can see the rubber torus inside the pulley. The rubber is what fails and causes the pulley to wobble. You may need to borrow a puller to get the pulley off.

2.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
  3. Remove or disconnect the following:

    Belt splash shield Accessory drive belts. Refer to Belts. Crankshaft center bolt and remove crankshaft damper.

    jturcotte_2368.gif

    Fig. Splash shield removal-2.5L engine

    jturcotte_2369.gif

    Fig. Crank damper and bolt- 2.5L engine

To install:
  1. Clean crankshaft snout and crankshaft damper bore.
  2. Install or connect the following:

    Crankshaft damper. Crankshaft bolt and torque to 143 ft. lbs. (182 Nm) Accessory drive belts. Refer to Belts. Belt splash shield

Oct 05, 2011 | 1999 Chrysler Cirrus

1 Answer

So ummm when ur engine vibration dampner just goes flying from under the car, what do u suggest. and no im not getting rid of it lol. but how would that be possible to just rip off??? cuz it just happened...


sometimes the rubber bladder takes a dump and the outside of the pulley just comes off. if the whole pulley came off it sounds like the crank pulley bolt either was not tight or gone. if you recently had a timing belt replaced that might be what caused it.

Sep 14, 2011 | 1987 Toyota Supra

2 Answers

Where is the crankshaft sensor on a 3.8L in a 97 buick lesaber


Hi,
The sensor is located to the right of the crankshaft behind the vibration dampner (harmonic balancer). You will need a balancer puller and a special tool to space the new sensor correctly.
(can be done also with eye spacing, but the tool is recommended to ensure proper spacing as to prevent damage to new sensor and / or harmonic balancer.) You will also need a strap wrench to hold balancer pulley in place while removing and re-installing balancer to crankshaft bolt. (helper required)

Procedure for replacement:
Remove negative battery cable.
Set parking (emergency) brake.
Release tension on serpentine drive belt and remove belt from harmonic balancer pulley. ( large pulley at bottom of engine)
Break loose lug nuts on passenger side front tire, do not remove bolts yet.
Raise and support vehicle on passenger side, remove wheel.
Remove plastic splash guard (cover) from passenger side wheel well.
Remove dampner / balancer center retaining bolt (counterclockwise, it is torqued very tight.) Use a strap wrench around pulley and have a helper hold that in place while using a 1/2" breaker bar and socket to turn pulley bolt out of crankshaft. Be careful not to rotate engine in a counterclockwise direction while breaking the bolt loose.
Using balancer puller, remove dampner / balancer pulley from engine.
You will now see the crank sensor to the right of the crankshaft bolted to the timing cover.
Disconnect sensor wiring and remove retaining bolts, remove sensor.
Put new sensor in place and screw in bolts, do not tighten them yet.
Reconnect wiring to sensor.
Now use special tool to properly space sensor. If you cannot find one at the parts store, you can space the sensor with the balancer pully held in place (not installed yet) and space the sensor evenly with the veins on the hub of the balancer pulley. Take your time and be sure it is as evenly spaced as possible.
Tighten sensor bolts.
Clean balancer hub free of any oil and dirt deposits using brake or carbeurator cleaner.
Reinstall balancer to crankshaft by tapping around the inner surface of pulley with a rubber hammer.
It is a press fit, so be sure you have it started evenly and progress slowly in a circular motion to ensure you are keeping it aligned straight with the crankshaft.
Reinstall balancer bolt using the same method as removal, torque bolt to 110 foot pounds, then tap around balancer again twice with rubber hammer, turn the engine 2 full revolutions clockwise using the balancer to crankshaft bolt, then tighten bolt an additional 1/4 turn.
Replace splash guard, put wheel on tightening lugs to finger tight and then wrench tight in a star pattern.
Lower vehicle until wheel makes contact with floor, tighten lug nuts to 115 foot pounds in a star pattern using a torque wrench.
Fully lower vehicle, remove jack.
Re-install serpentine drive belt
Re-connect negative battery cable.

End of procedure....Hope that helps!.....Mike

Jun 25, 2011 | 1997 Buick LeSabre

2 Answers

I need to replace a thermostat on a 2002 isuzu rodeo. 6 cylinder motor. I heard a few rumors that i got to take apart the intake manifold to get the the housing for the thermostat. I followed the upper...


Hi, I think you're on the right track. Here are instructions from autozone.com:

3.2L & 3.5L Engines
  1. Disconnect the negative battery cable.
  2. Drain engine coolant from the radiator and engine.
  3. Disconnect radiator hose from the inlet pipe.
  4. Remove the thermostat housing, then remove the thermostat (2).
jturcotte_1728.gif

Fig. Exploded view of the thermostat housing (1), thermostat (2) and outlet pipe (3)



To install:
  1. Install the thermostat into the outlet pipe (4) making sure that the air hole is in the up position.
  2. Install thermostat housing and tighten the bolts to 18 ft. lbs. (25 Nm).
  3. Attach the radiator hose to the inlet pipe.
  4. Refill the engine with the proper type and amount of coolant.
  5. Connect the negative battery cable.
  6. Start engine and check for coolant leakage.

May 18, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

1996 Lincoln Town Car. A/c will not blow out cool air. All things under the hood seems to be working correctly(sweaty/cold line, a/c compressor comes on, system has been recharged with no sign of leak,...


Control dampner switch okay from looking at the fron of the car on the passenger side youll see a group of vacuum hose plastic connecting to a junction make sure none of the are broken Two of the control the vent control and inside tempurature. Once it disconnect you no longer have mixture control. Do you remember when it was working fine and you turn off the car and you heard that little hissing noise? Well that line is now disconnected

Apr 23, 2011 | 1996 Lincoln Town Car

1 Answer

How do you remove the dampner pulley on a 1998 potiac 3800 engine


  1. remove the right front tire and inside fender cover to see crank pulley.
  2. remove the belt, use a rachet to release the tension off the belt, i've enclosed a diagram of the belt and the tensioner.
  3. remove the center bolt on the crank pulley.
  4. using a puller remove the pulley.
  5. reverse directions to install.
  6. i hope this is helpful
  7. 4399c71.gif

Oct 31, 2010 | 1998 Pontiac Grand Prix

1 Answer

Location of the water pump


hi
Its in with the timing belt
The pump cost about $90cnd. you don't have to replace the timing belt if it is in good condition although I would recommend it. First you must remove the passenger side front wheel, and the splash guard. Then you must take of the accesory drive belts. The one on the alternator, and the one on the powersteering/air conditioner. Then you must take off the timing belt cover, mark your timing, remove the tensioner and the belt the camshaft gears the idler pulley and the crank shaft dampner. Then the rear timing belt cover comes off and you can access the water pump. Install the new pump and reassemble. Make sure the crank dampner and the camshaft sprokets are seated ALL THE WAY BACK, (or you'll cause yourself all kinds of problems.) When the timing belt goes back on make sure you line up the timing correctly, you can't start the engine till it is all back together and if your timing is out it won't run right or might not even start. I would not recommend taking on this job if you don't have the slightest clue of what you are doing as there is a lot to go wrong (timing is set correctly can screw up your engine), and do attempt it if you don't intend spending alot (like 10hrs) of time on it to do it right.

Jul 13, 2010 | 2000 Dodge Neon

3 Answers

My belt keep coming off the idler polley


Check the alignment of the pulleys. Most common problems are: 1) Belt tensioner. 2) Idler Pulley. 3) Crank Pulley (Vibration Dampner)

Mar 08, 2010 | 1995 GMC Jimmy

2 Answers

How do I access oil filter on 2007 HyundaI Accent?


well i hate to tell you that your going to have to get dirty on this one.. might want to put on some old overhauls.. jack up the car on the drivers side. then make sure it is secure with some jack stands properly in place.crawl under the car and you should see it some where on the motor. it will be a can looking thing. they make a special wrech to take it off with and put a new one on. you wil need an oil catcher to catch the oil also.
hope that helps good-luck, ray

Jan 16, 2009 | Hyundai Accent Cars & Trucks

3 Answers

My heat in my truck doesnt work


the blendoor on the heater box maybe broken ck lines going to heater core and make sure they are hot. does the heat temp change at all from cold to hot?

Dec 05, 2008 | 2001 Ford Expedition

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...