Question about 2004 Chevrolet Aveo

1 Answer

Keyless entry not working

Will not unlock with either key fob. can't push down lock on the door when exiting, i have to use the key to lock the door. the other locks i can push down.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

Replace the battery. Take it to Oriellys and they have a tester at the front counter.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Nissan Sentra, the keyless entry locks the doors but does not unlock them.


does your unlock button work in car? If it does, do you have another keyless entry key fob? If so does it work? If you just replaced the battery you can try removing battery and cleaning contacts within remote. I know some of the nissan altimas had the same issue and the only solution was a new key fob. Good Luck

Jan 04, 2013 | 2005 Nissan Sentra 1.8

1 Answer

99 blazer keyless entry


I don't know if this is procedure you followed? There is door lock receiver under the dash. The receiver sends message to bcm the bcm controls the door lock/unlock relays accordingly. Any applicable trouble codes?
key fob 1-vnyhs4jhflyzha3kfclvoh0h-5-0.jpg

Mar 22, 2017 | 1999 Chevrolet Blazer

1 Answer

Keyless entry wont work 2002 chevy s10 LS


try this procedure to reporgram:

1. Close all vehicle doors.

2. Insert the key into the ignition.

3. Hold down the power UNLOCK button on the driver's continue to hold down until instructed
to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.

5. Turn the key to the ON position (as far as you can go without starting the engine).

6. Turn the ignition switch to the OFF position.

7. Turn the ignition switch to the ON position.

8. Turn the ignition switch to the OFF position.

9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the vehicle locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode

Jun 30, 2009 | 2002 Chevrolet S-10

1 Answer

How to program key fob. I have the fobs.


Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Jun 25, 2009 | 2002 Chevrolet Tahoe

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

1 Answer

How to program a keyless entry fob for 2005 gmc envoy - i am replacing the battery in my key fob every 5 days. I have to be right next to the car for it to work. Any idea what would cause this. I ordered a...


Seating in the drivers seat , make sure all doors are closed.Insert key into ignition, don't turn on yet.
Wait for the dome light to go out, then press and hold the door unlock button , make sure it is UNLOCK, while turning the key ON OFF ON OFF Twice , do not engage the started, just on to the point of being on. Release the unlock button,and your doors should lock, then unlock indicating programming mode.At this point hold down both the lock and unlock button on the key fob. After 30 seconds your locks should lock and unlock, indicating the fob is programmed. This must be repeated for all remotes, whether or not it be new or old. After all remotes are programmed, turn the key off and on again to exit programming mode.

May 18, 2009 | 2005 GMC Envoy

1 Answer

2004 Chevy Impala Keyless Entry System Stopped Working


HOPE THIS HELPS YOU MIGHT WANT TO REPROGRAM THAT KEYLESS ENTRY FOB.. JERRY
. Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.

2. Press and hold the DISP button on the radio for at least five seconds until settings is displayed.

3. Press the SEEK up or down arrows until FOB PROG appears on the display.

4. Press the PREV or NEXT button to enter the submenu. The current selection will have an
asterisk next to it. BEGIN will be displayed.

5. Press the DISP button to start programming. When the message PUSH FOB flashes, press and
hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A
chime will be heard to verify the transmitter is learned.


6. Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press
the DISP button again, just press down the LOCK and UNLOCK buttons on the next transmitter
to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

Apr 27, 2009 | 2004 Chevrolet Impala

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

3 Answers

Remote keyless entry not working


KEY FOBS FOR THIS MODEL MUST BE PROGRAMED USING A TECH 2 SCAN TOOL SO IT MUST BE DONE AT THE DEALERSHIP FOR ABOUT HALF HOUR LABOR HOPE THIS HELPS

Mar 28, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

My car is acting crazy!


" turn the key on engine off 8 times. the doors will lock and unlock. push one of the buttons on the key fob and the doors will lock and unlock. do this for each remote that you have. when you are done turn the key off. the door locks will lock and unlock. the remote fob should work after this."
From My SecuriLock..

Sep 05, 2008 | 2006 Ford Taurus

Not finding what you are looking for?
2004 Chevrolet Aveo Logo

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...