Question about 2004 Dodge Intrepid

1 Answer

Where do you locate the cam position sensor on a dodge intrepid 2.7L?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,420 Answers

Right side of head open hood standing in front look down to right side head the little black 90 deg with an electrical connection thats it disconnect wiring harness one bolt remove it pull sensor straight out there you go need me e-me .LEE

Posted on Dec 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam sensor


On front of the timing covers...

Apr 21, 2014 | 2003 Dodge Intrepid

1 Answer

Cam shaft position sensors


In my 3.5L HO cps is located front top left, just under edge of upper intake manifold, maybe an inch and a half aft of timing cover. I replaced mine, easy enough.

Jan 02, 2014 | 2004 Dodge Intrepid

1 Answer

I have a 2001 dodge intrepid. I just replaced the output speed sensor. It is still stuck in limp in mode.


There is a recall on some intrepids for the cam position sensor. You may have to change the cam sensor, if you don't have a code for it, don't change it. You might have to go to the dealer and have them flash your computer with a scan tool. that may be covered under the recall. I would investigate if I were you.

I hope this helps

Aug 06, 2010 | 1998 Dodge Intrepid

1 Answer

How to change cam positiom sensor in 2000 dodge


The cam position sensor on the 2.7 engine is on the
driver side of your engine, right in the front of the head. there's a 10mm bolt. undo the bolt and pull it straight out. push the new one into the hole, and hold pressure on it until it's bolted back in.

If you have the 3.5, the cam position sensor is located on top of the timing cover. I just unbolt the upper intake just enough to lift it up a little. unbolt the cam sensor, pull it out and install the new one keeping pressure on it until it's bolted in.

I hope this helps

May 13, 2010 | 2000 Dodge Intrepid

2 Answers

CAN NOT LOCATE THE CRANKSHAFT POSITION CENSOR ON MY 1996 INTREPID


It should be on the transmission by the passenger side of car. It has three wires connected to it.
1998 Dodge Intrepid
the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.
1994 Dodge Intrepid 3.3 liter

Jan 01, 2010 | 1996 Dodge Intrepid

1 Answer

How to replace the Cam position sensor?


You didn't state what engine you have. If you have the 2.7 L, the cam position sensor is bolted right to the front of the left cylinder head. Disconnect the wire, remove the bolt, pull out the sensor. Be gentle inserting the new sensor, and make sure the bolt hole is aligned while installing it, so the sensor isn't damaged by contact with the camshaft.

I'm not sure where the sensor is located on a 3.5 L, but I would suspect it is similar.

Dec 24, 2009 | 2002 Dodge Intrepid

1 Answer

Locate cam position sensor on 2004 dodge intrepid


The camshaft position sensor is mounted to the top of the timing case cover.

Oct 25, 2009 | 2004 Dodge Intrepid

2 Answers

Where is the camshaft position sensor located on a 2000 Dodge Intrepid?


If it is a 3.5 it is located on the front of the engine on the drivers side under the plenum.

Oct 23, 2009 | 2000 Dodge Intrepid

1 Answer

Where is the camshft position sensor on a 03 dodge intrepid 2.7l Bank A


THE CAM SENSOR IS LOCATED IN LEFT(DRIVER'S SIDE) CYLINDER HEAD AT THE FRONT..1 BOLT AND A 3 WIRE CONNECTOR..REMOVE BOLT AND PULL SENSOR OUT TOWARD FRONT OF VEHICLE..YOU MAY HAVE TO WIGGLE SENSOR TO REMOVE..PICK UP A NEW ONE AND YOU WILL SEE WHAT IT LOOKS LIKE..PRETTY EASY TO REPLACE AND IS FAIRLY COMMON PROBLEM

Aug 29, 2009 | 2003 Dodge Intrepid

Not finding what you are looking for?
2004 Dodge Intrepid Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...