Question about 2004 Toyota Camry

2 Answers

I accidentally touched the flasher dashboard switch. Now the flashers are on and will not turn off. I have pulled the fuse to get them off and now I have no turn signals. Help! pleas Marcia W

Posted by on

  • mwilmes Oct 06, 2009

    I had already tried replacing the fuse on my flashers that won't turn off. It did nothing. I have also taken off the battery cable to try to get a system reset and it did not work.

  • mwilmes Oct 06, 2009

    Hi Is replacing a turn signal switch something I can do? Can I get the switch at an automotive parts store?

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 76,630 Answers

The only way to correct this is to replace the turn signal switch, to do this you must remove the covers from the steering column, the screws that hold them together are located in holes under the bottom of the steering column, I think there are four, they should be Phillips head screws, remove the covers and then remove the 2 screws holding the turn signal switch to the column, disconnect the wiring connector to the switch and remove it, reverse this to install new switch.

Posted on Oct 06, 2009

  • yadayada
    yadayada Oct 06, 2009

    yes u will need to replace the switch, here is the part number and the price.





    STANDARD MOTOR PRODUCTS Part # CBS1021
    w/o Foglight, Daytime Running Lights; U.S. Models $104.79




    STANDARD MOTOR PRODUCTS Part # CBS1127
    w/ Foglight, Daytime Running Lights; U.S. Models $111.79

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Try putting the fuse back in and see if they have shut off. it sounds as tho the flasher unit has failed and needs to be replaced.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LXI. how do I replace flasher?


The Flasher is located: Behind A/C and heater control panel, in center console.

Flashers

Print
REPLACEMENT

Flashers are located either on the bottom of the fuse block or on a module under the dashboard. They are replaced by simply pulling them straight out. Note that the prongs are arranged in such a way that the flasher must be properly oriented before attempting to install it. Turn the flasher until the orientation of the prongs is correct and simply push it firmly in until the prongs are fully engaged.clink on link to see what flasher look's like.
http://www.autozone.com/electrical-and-lighting/turn-signal-flasher/novita-turn-signal-flasher/chrysler/sebring/1998/4-cylinders-y-2-0l-mfi-dohc/193143_0_7283

Aug 15, 2015 | 1997 Chrysler Sebring

1 Answer

Where is the flasher unit located


The flasher is located under the dashboard close to the steering column. you have to turn it on to make a clicking sound.... and feel for it... when you touch it you will know it is it... just pull it out. But before you do that....CHECK THE FUSES.

Sep 06, 2014 | Cars & Trucks

1 Answer

Turn signals stopped working but were working yesterday. Any ideas?


More than likely the electronic turn signal flasher is defective.
Instructions
  1. Remove the Old Flasher Relay
    • Using your socket wrench, disconnect the negative cable from the car's battery terminal. The negative terminal and cable are identified on the top of the battery using the minus ("--") symbol. Once the cable is disconnected, wrap the metal end completely with the black electrical tape. Lay the cable down and make sure it's not touching any metal surfaces.
    • 2Open the driver side front door and kneel or position yourself so that you're able to see under the dashboard.

    • 3Locate the automotive flasher relay under the dashboard on the right-hand side. The flasher relay is about the same size as an ice cube. It will be held in place by one screw and will have a three-pronged wiring harness connected to it.
    • 4Remove the screw holding the flasher relay in place and slowly lower it from underneath the dashboard.
    • 5Hold the flasher relay in one hand, and with the other hand gently disconnect the wiring harness plug from the relay. Never separate the flasher relay by pulling the harness off by the wires, always hold the plastic harness plug itself.
    Install the New Flasher Relay
    • 6Inspect the new flasher relay to make sure it isn't damaged. Hold the new flasher relay and the old one side by side and compare them, ensuring that they are exactly the same.
    • 7Carefully plug the wiring harness connector into the new flasher relay. Make sure no other wires are intertwined as you raise the flasher and harness back into position under the dashboard.
    • 8Secure the flasher relay by returning its mounting screw.
    • 9Unwrap the negative battery cable's connector and reattach it to the car's battery terminal. Turn the power on or start your car and test out the new flasher relay to make sure it's working properly

Nov 08, 2012 | 1998 Ford Taurus

1 Answer

Why dont headlights come on an ford f 250


Hazard and turn signals usually use separate flashers, switch the flashers to see if turn signals work and hazards don't, if so replace the flasher

you need to replace the blinker flasher unit

it is different from the hazard unit

they cost about 4 bucks

the flasher unit is the big round thing in the fuse panel in the dashboard


Oct 05, 2012 | 1988 Ford F 250

1 Answer

How to change flasher unit 0n 2002 Saturn L-series


WARNING The flasher unit for turn signals should not be switched with a flasher unit for the hazard lights. To check the filaments of all of the turn signal bulbs and the brake lights, turn on the hazard flashers and walk around the car.
A flasher can be located in the fuse panel, under the dash in the wiring loom, in a glove box, under the hood, or somewhere else.
f36-02.jpg A fuse panel. Most flashers are located under the dashboard on the driver's side. When working properly, a flasher is easy to locate because it makes a ticking sound. When it is not functioning, a service manual may be needed to help locate it. Lighting company catalogs generally have pages listing the location of flashers.
To replace a flasher:
  • A flasher features two or three prongs that plug into a socket.
  • Just pull the flasher out of the socket and replace it with a new one.

Aug 24, 2012 | 2002 Saturn L-Series

1 Answer

Where is the flasher located


there are most likely two, plugged into a fuse panel. there are most likely two fuse panels, a small one with a few large fuses under the hood and another larger panel with many small fuses inside under the dashboard. if you pull out and read your owners manual, you will find its exact location. replacement owners manuals can be had on eBay. the two flasher units are generally the same part and can be swapped. so if you think your turn signal flasher is bad just swap in the emergency flasher. if they then work, go buy another flasher unit, if they do not work then you have a problem elsewhere.

Feb 03, 2011 | 1995 GMC Sonoma

2 Answers

No hazard or turning signal


check fuses. If OK, replace flasher unit. the flasher is a cylinder-shaped devide under your dashboard below the instrument panel, left of the steeringcolumn. It should pull straight out of the connector. You can buy a new one at the parts store and even at WALMART, etc. Make sure to get the one that fits your car--take the old one with you.

Sep 01, 2010 | 1999 Chevrolet Venture

4 Answers

Turn signal or emergency flashers wont work. parts store says they cant find a flasher for them. I checked the turn signal fuse and its good. Any ideas?


The flasher is located above the fuse panel. The relays are built into the switch itself. They have a recall on the 4 way flasher switch because it is faulty and causes blinkers not to turn on. Very common Malibu and other Gm problem

Nov 20, 2009 | 2002 Chevrolet Malibu

Not finding what you are looking for?
2004 Toyota Camry Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...