Question about 1986 Dodge D150

Open Question

Can you replace just the clutch pedal? - 1986 Dodge D150

Posted by on

  • Dana Newcombe
    Dana Newcombe May 11, 2010

    Yes, but, what are you tyring to accomplish by doing this.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get to Chevy s 10 1998 clutch pedal upper pin and bushing


CLUTCH PEDAL REPLACEMENT (CLUTCH) Document ID# 46043 Clutch Pedal Replacement

Removal Procedure



  1. Remove the master cylinder rod from the clutch pedal.


  2. Remove the clutch pedal from the support by depressing the side tabs.

Installation Procedure



  1. Position the clutch pedal into the support.


  2. Secure the master cylinder rod to the clutch pedal.

Good Luck

Aug 11, 2016 | Cars & Trucks

1 Answer

Where is the break safety switch located in a 2009 Ford Fusion


Jeanette, break switch is above brake pedal arm, safety neutral switch is on transmission, clutch pedal safety switch above clutch pedal arm. Links below have pics.
to show your appreciation press the helpful button and follow me on fixya for more tips and info.

06 ford fusion brake light switch replace

How To Test and Replace the Neutral Safety Swtich Inhibitor Switch P0705

Clutch switch behind clutch pedal Ford Focus Forum Ford Focus ST Forum...

Replace master cylinder clutch Ford Focus Forum Ford Focus ST Forum Ford...

Feb 15, 2016 | 2009 Ford Fusion

1 Answer

Broken clutch pedal replaced and no stuck


replace the master cylinder as there are burrs and grooves in the cylinder that is jamming the piston movement.

Mar 02, 2014 | Kia Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

Clutch pedal travel is excessive. Sits about 2"


A clutch pedal takes MUCH more travel to function correctly, when compared to a brake system...

A clutch needs to be replaced (maybe) when it SLIPS, Chatters, Or fails to release...

Other than that, the clutch will need to be adjusted to allow for total release of the relese bearing when pedal is released, and full disengaugement when pedal is depressed....Have a mechanic look at the adjustement, as proper adjustment gives longer clutch life. This is a periodic adjustment item.

Apr 03, 2011 | 2001 Subaru Impreza

1 Answer

2001 Honda Accord Clutch Issue


check the actual pedal and clutch linkage.  Also look for a fitting thats emitting air into the system.

Mar 24, 2009 | 2001 Honda Accord

1 Answer

2002 Civic Dx Clutch?


i have just replaced an 03 civic ex clutch and transmission bearings due to a customer being too harsh on it. It sounds like its got a little life left in it if you are easy on it. 

if there is adjustment in this model use the below walkthrough to adjust it.

adjust the clutch pedal, 

1. if you look up on the top of the clutch pedal, the first thing you should see if a clutch pedal position switch, and right behind it there is a locknut, looens the locknut. once you loosen it, back off on the pedal position switch or adjusting bolt untill it no longer touches the clutch pedal. 

2. now behind the clutch pedal, there is a pushrod. and on that pushrod, there is a locknut, loosen that locknut. Now turn the pushrod in or out to get the desired height and stroke at the clutch pedal. 

The freeplay is the amount of push on the clutch pedal to where is starts to have resistance from the top. I have usually been told it should be set at 1 1/2-2 inches of freeplay.

Once you set it, tighten the locknut on the pushrod. With the clutch pedal released, turn in the clutch pedal position switch untill it contacts the clutch pedal. then turn it an additional 3/4 to 1 turn. And tighten the locknut.

Now on top of the clutch pedal switch, there is a clutch interlock switch. Loosen the locknut on that switch. then press the clutch pedal to the floor.

release the clutch pedal 15-20 mm (0.59-0.79 in) from the fully pressed position, and hold it there. adjust the position of the clutch interlock switch so the engine will start with the clutch pedal in this position. then tighten the locknut on that switch.

Hope this helps 

Nov 28, 2008 | 2002 Honda Civic

2 Answers

Clutch Problem


Check your Master Cylinder

Jul 15, 2008 | 1984 Pontiac Fiero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...