Question about 2000 Chevrolet Blazer

1 Answer

How do I replace the rear wheel bearing in a 2000 chevy blazer

Posted by on

  • Patrick OCarroll
    Patrick OCarroll May 11, 2010

    Are you familiar with HAYNES manuals.My suggestion would be BUY ONE.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

I am sorry to tell you this, but you will have to take the Truck to a Rear End repair shop to do this. If you are very mechanically inclined and have all the specific tools like a slide hammer, bearing puller, bearing installation tool, etc. If you have tools like this, then I would get yourself the car manual. To replace the bearings you will have to remove the axles.

Posted on Oct 06, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 112 Answers

SOURCE: wheel bearing

the part can run from 150-200 and its about 2 hours labor(is this a 4x4?

Posted on Apr 19, 2009

  • 14 Answers

SOURCE: 2000 chevy 4 wheel drive blazer, locked in 4 wheel

check / replace the front axle actuator

Posted on Jun 21, 2009

emissionwiz
  • 75744 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

SOURCE: how to put wheel bearing on a chevy blazer rear

Pull axle and have auto part store install new bearing

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flat tow or dolly towing for an 2000 S10 Chevy Blazer


If you dolly it you put wear on the wheel bearings and ring and pinion in the differentials on the front or rear depending on what axle you raise.

Mar 14, 2015 | 2000 Chevrolet Blazer

1 Answer

Need to take rear driveline out of 1998 chevy blazer


By removing the drive line you may move the car but it will lock up on you at some point,, the rear end, wheel bearing or broken axel will cause more damage, just tear into it and fix the problem before it causes you more trouble.....Hope that helps...

Feb 26, 2015 | 1998 Chevrolet Blazer

1 Answer

2000 Chevy Blazer 4x4...started making a horrible loud noise after my cruise control went out. I have recently replaced my hub and the brake pads and the CV axle. The noise comes and goes and only happens...


does it get louder above 45-60mph? and much quieter at low speeds. It could be wheel bearings, a rear differential or front differential. If its a grinding humming noise its wheel bearings, listenin to see if theyre coming from the front or rear, left or right, or both when your driving to know what wheel bearing are bad. If its a whinning noise, its probably a differential. check and listen to hear if its coming from the front or rear. Also, check for loose plastic around the wheels. Lastly check your tires for uneven or choppy wear. move your hands front to back on the top of the tire. does it feel really choppy and rough, maybe you just need new tires

May 04, 2011 | 2000 Chevrolet Blazer

1 Answer

Vibration NOISE in front end of 2000 Chevy Blazer. Any suggestions??


Check the front wheel bearings .... very common . While driving turn the wheel gently from side to side and see if the noise changes .. this will load and unload the bearings.

Feb 12, 2011 | 2000 Chevrolet Blazer

1 Answer

What is the rear wheel bearing gear ratio for a 2001 Chevy Blazer 4WD - 2 door?


I think you mean the rear end ratio. there is no gear ratio for the wheel bearing. If you look at the factory sticker on the drivers door, there will be an "axle code". write that down and then look here for the ratio.

http://www.drivetrain.com/parts_catalog/ring_and_pinions/what_gear_ratio_do_i_have_in_my_gm_or_chevrolet.html

Jan 05, 2011 | 2001 Chevrolet Blazer

1 Answer

How to put wheel bearing on a chevy blazer rear


Pull axle and have auto part store install new bearing

Mar 27, 2010 | 2000 Chevrolet Blazer

2 Answers

Strange wobble noise


your bearings. thats what it sounds like to me. if it almost sounds like you have a big rock just jumbling around in your tire thats most likely your bearings. its pricey but its worth it to get it fixed. if thats not it check into your transfer case and your shocks

Feb 23, 2010 | 2000 Chevrolet Blazer

3 Answers

How replace turn signal switch 2000 chevy blazer?


Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Oct 07, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...